Vectronix PLRF10C - User Manual

Questions and Answers

A
aaron07Aug 14, 2025
How to fix Vectronix Measuring Instruments when measurements can't be taken?
- A
  Allison DavilaAug 14, 2025
  If your Vectronix Measuring Instruments are not functioning, consider these potential causes and solutions: * **Batteries have run out:** Replace the batteries. * **Battery contacts corroded:** Clean the battery contacts. * **Low temperature:** Warm up the batteries, as low temperatures can reduce their performance. * **Extreme heat:** Avoid storing the batteries at temperatures exceeding +70°C to prevent shortening their lifespan.
L
Leslie MillsAug 17, 2025
What to do if Vectronix PLRF10C display "- - - -" after distance measurement?
- J
  James WrightAug 17, 2025
  If you see "- - - -" displayed after a distance measurement on your Vectronix Measuring Instruments, it could be due to the following reasons: * **Distance outside specified range:** Ensure that the distance you are measuring is within the instrument's specified measurement range. * **Object too small or inaccurately targeted:** Make sure the object is appropriately sized and accurately targeted. * **Bad weather conditions:** Consider that weather conditions can affect measurement range.
P
Pam OrozcoAug 21, 2025
Why Vectronix PLRF10C show inaccurate azimuth values?
- A
  Anthony SimpsonAug 21, 2025
  Inaccurate azimuth values on your Vectronix Measuring Instruments can stem from these issues: * **Incorrect declination setting:** Ensure the declination is set correctly. * **Disruptive magnetic fields:** Be aware of and avoid disruptive magnetic fields at the measuring position. * **Bad compensation constants:** Perform compass compensation.
M
Michelle RyanAug 25, 2025
What does "LobA" mean on Vectronix Measuring Instruments and how to fix it?
- K
  Kathleen PattersonAug 25, 2025
  If your Vectronix Measuring Instruments display "LobA", it indicates that the battery is almost depleted. Replace the battery to resolve this issue.
N
Nicholas NguyenAug 27, 2025
What to do if Vectronix PLRF10C Measuring Instruments display "GAtE" after distance measurement?
- R
  Rebecca SinghAug 27, 2025
  If your Vectronix Measuring Instruments show "GAtE" after a distance measurement, it means the measured distance is below the selected distance gate. To fix this, reduce or turn off the distance gate.
R
Randall HallAug 31, 2025
Why Vectronix PLRF10C measure objects in front or behind the intended object?
- P
  Patricia RiceAug 31, 2025
  If your Vectronix Measuring Instruments are measuring objects in front or behind the intended object, it might be because "3dOF" is selected in the configuration menu, which displays only the distance with the highest return signal. To correct this, select "3dOn" in the configuration menu.
M
Margaret WilliamsSep 3, 2025
What does "ntOn" displayed after a measurement on Vectronix PLRF10C Measuring Instruments mean and how to resolve it?
- A
  Alexander ThomasSep 3, 2025
  If "ntOn" is displayed after a measurement on your Vectronix Measuring Instruments, it indicates that the device is being used during daylight conditions with "ntOn" selected in the configuration menu. To resolve this, select "ntOF" in the configuration menu.
M
Michael PerrySep 6, 2025
How to make the electronic reticle visible on Vectronix PLRF10C?
- S
  Steven Griffin Jr.Sep 6, 2025
  If the electronic reticle is not visible on your Vectronix Measuring Instruments, and "ErOF" is set in the configuration menu, select "ErOn" in the configuration menu to make it visible.
K
Katherine GrantSep 10, 2025
What causes the azimuth measurement symbols on Vectronix PLRF10C Measuring Instruments?
- K
  Kenneth McintyreSep 10, 2025
  If you observe a series of underscores displayed during azimuth measurements on your Vectronix Measuring Instruments, it signifies that the allowed inclination and / or tilt angle has been exceeded. Ensure you stay within the specified inclination and / or tilt angle to resolve this.

Vectronix PLRF10C Specifications

General

Type	Laser Rangefinder
Accuracy	± 1 m
Laser Wavelength	1550 nm
Magnification	7x
Field of View	7°
Storage Temperature	-40 °C to +70 °C
Protection Class	IP 67
Power Supply	Rechargeable Li-ion battery
Laser Class	Class 1M

Summary

Purpose of Equipment

General Information

Safety Notices and Device Limitations

Provides information on safety class, intended purpose, limitations, inappropriate use, and hazards.

Care and Cleaning Procedures

Lens Cleaning Instructions

Instructions on how to clean the lenses, including handling fingerprints and particles.

Casing and Cable Maintenance

Guidance on cleaning the device casing and interface cable socket and cable.

Technical Data - Optics and Compass

Optical Specifications Overview

Details the optical specifications of the device, including magnification and field of view.

Magnetic Compass Technical Details

Provides technical data for the magnetic compass, including range, accuracy, and resolution.

Technical Data - Rangefinder Performance

Rangefinder Performance Metrics

Details laser type, eye safety, range performance, accuracy, and beam divergence for the rangefinder.

Technical Data - Miscellaneous

Miscellaneous Device Specifications

Covers power supply, dimensions, tripod interface, and data interface specifications.

Getting Started Guide

Battery Replacement Procedure

Step-by-step guide on how to replace the device batteries and indicators for battery status.

Diopter Adjustment Guide

Instructions for adjusting the diopter for a sharp image and personal setting reminders.

Reticle Options and Usage

Explains the glass and electronic reticles, including line spacing and mil conversion.

General Operations and Key Functions

Distance Measurement Principles

Factors Affecting Measurement Range

Illustrates factors like reflective properties, target size, and atmospheric conditions affecting measurement range.

Complete Measurement with Data Transfer

Guides on performing complete measurements including slope distance, azimuth, and inclination with data transfer.

Multiple Object Measurement Techniques

Details how to obtain up to three separate distances in a single measurement with the '3dOn' feature.

Measuring Distance Between Two Objects

Explains the procedure to measure the distance between two distinct objects.

Horizontal and Vertical Distance Measurement

Describes how to measure horizontal ('Hd') and vertical ('Ud') distances to an object.

Azimuth and Inclination Measurements

Factors Influencing Azimuth Accuracy

Explains factors like metal objects and magnetic fields affecting azimuth accuracy and countermeasures.

Performing Azimuth Measurement

Step-by-step guide on how to perform an azimuth measurement using the device.

Performing Inclination Measurement

Details the procedure for measuring inclination angles with the device.

Device Configuration

Navigating Configuration Menu

Guides on navigating the configuration menu to switch instrument functions on and off.

Configuring Multi-Distance Measurement

Explains the '3dOn' function for measuring up to three distances in a single shot.

Configuring Electronic Reticle

Describes the 'ErOn' function to activate the electronic aiming mark for low light conditions.

Configuring Night Vision Mode

Explains the 'ntOn' function for reducing display brightness for night vision use.

Night Vision Operation - Mounting

Instructions on how to attach and set up the night vision device with the PLRF.

Night Vision Operation - Removal

Details the steps for removing the night vision adapter and disabling the night mode.

Device Settings

Setting Measurement Units

Guides on setting angle and distance measurement units like meters, yards, feet, degrees, and mils.

Distance Gate Configuration

Explains how to limit the closest distance the device will measure using the distance gate function.

Declination Management

Declination Display and Settings

Explains declination, its variation, and how to set it for grid north or magnetic north.

Declination Setting and Correction

Provides steps for setting and correcting the declination value on the device.

Resetting to Factory Default Settings

Instructions on how to reset the device to its default factory settings.

Compass Compensation

General Compensation Guidelines

Explains the types of compensation (12-point, 4-point), when and where to perform it.

Compensation Movement Instructions

Details the specific movements (UP, dn, ro90°, hori, undo, tFAr) required during compensation.

Performing Compass Compensation Procedure

Guides on initiating and performing the 4-point or 12-point compass compensation procedure.

Interpreting Compensation Results

Interprets the results of compass compensation (Good, bAdC, rESC) and possible causes of failure.

Built-in Test Function

Troubleshooting - Measurement Issues

Troubleshooting: No Measurement Function

Covers issues like dead batteries, corroded contacts, or temperature effects impacting device function.

Troubleshooting: No Distance Detected (- - - -)

Addresses issues where no distance is detected, due to range, target size, or weather.

Troubleshooting: Distance Gate Display (GATE)

Explains the cause of 'GATE' display related to distance gate settings.

Troubleshooting: Azimuth Measurement Symbols

Interprets symbols indicating tilted too far (up, down, left, right) during azimuth measurements.

Troubleshooting: Inaccurate Azimuth Values

Covers causes like incorrect declination, magnetic interference, or bad compensation constants.

Troubleshooting: Compass Compensation Failures

Addresses issues with timing out of compensation or altered magnetic conditions.

Troubleshooting: Electronic Reticle Not Visible

Explains that the 'ErOF' setting prevents the electronic reticle from being visible.

Troubleshooting: Low Battery Indicator (LobA)

Explains that 'LobA' indicates low battery or cold conditions affecting battery performance.

Troubleshooting: Object Measurement Discrepancies

Addresses the '3dOF' setting where only the highest return signal distance is displayed.

Troubleshooting: Night Mode in Daylight (ntOn)

Explains that 'ntOn' in daylight conditions means the night mode is active.

Data Transfer Operations

Connecting the Interface Cable

Instructions on how to connect and disconnect the interface cable to the device.

Data Transfer Formats and Parameters

Details interface parameters like baud rate, parity, and data bits for PC, PLGR, and GARMIN connections.

Equipment and Parts Information

Standard Parts List and Spare Parts

Lists the standard extent of delivery and available spare parts for the device.

Available Optional Accessories

Details optional accessories such as data cables, night vision adapter, and tripods.

Options and Interface Settings

Setting Interface Options

Guides on setting up different interface options for connecting to PC, PLGR, or GARMIN.

Overview of Interface Settings

Provides an overview of PC, PLGR, and GARMIN interface settings and their purpose.

PLGR+96; PLGR II Specific Settings

Instructions for setting up the PLRF for PLGR and configuring PLGR+96/PLGR II.

GARMIN GPS Integration Settings

Guides on setting up the PLRF for GARMIN connection and configuring GARMIN GPS units.

Fall of Shot (FOS) Measurement

Customer Service and Support

Vectronix Quality System Information

Details Vectronix's quality management system (ISO 9001, ISO 14001) and commitment to customer satisfaction.

Related product manuals

Vectronix PLRF10

34 pages

Vectronix PLRF15