ViewSonic PJD6531w User Manual

A Flag Output signal indicates if the lamp has lit rightl y. The
Start Control Input and the Flag Output are mains isolated.
Output Protection short circuit +output / - output for max. 10s
No protection for output short to GND
Safety Standards IEC60950, UL60950
Note:
7
Measured at real lamp load. Deviations will occur on all kind of artificial loads (e.g. resistor)
8
Measured with RGB waveform. The noise deviation from customer generated UNISHAPE
waveforms should be controlled by the official appro val process.
Attention for handling
 Do not touch the lamp until it has cooled completely, because the lamp is very hot
during operation and immediately after turned off.
 The lamp has to be fixed firmly to the base or socket.
 Turn off the power supply duri ng maintenance.
 Do not hold the lamp except outer surface of the reflector.
 Wear protective gloves and eyeglasses when handling the lamp.
 Any unusual shock or vibration to the lamp should be avoided.
 The lamp contains the mercury. It s breakage might cause mercury to flow out of the
reflector. Please manage provision at the customer’s product.
 Do not pull the lead wire and plug by more than 24.5N.
 Please be careful of handling the lamp because it is made of glass.
 Please notice for keeping or handling the la mp, because there is a projection of this
lamp with reflector ahead.
 Do not touch the bulb and the mirror area of the reflector.
Attention for use
 Do not close or cover the lamp with any flammable stuff.
 During operation, the lamp is under extremely high p ressure. Please manage
provision at the customer ’s product to prevent fragments of bulb and mercury from
flowing out of it. If the lamp bursts in case of an emergency, the sound will be
occurred.
 Lamp operation should be with the specified lamp driver and the system ONLY.
 Do not look at the lamp directly during operations.
 Do not expose your skin directly. We recommend to you to put on something for
protection for your skin. For example, long sleeve shirt, gloves, glassed and so on.
 Do not modify the lamp a nd never use a lamp that has been modified.
 Any unusual shock or vibration to the lamp should be avoided during operation.
 Do not use any broken lamps.
 Dispose of used lamps according to your local instruction.
Confidential - Do Not Copy
ViewSonic Corporation
PJD6531w
10

ViewSonic PJD6531w Specifications

General

Native aspect ratio	16:10
Projection distance	1.2 - 10 m
Vertical scan range	50 - 120 Hz
Horizontal scan range	31 - 80 kHz
Projection technology	DLP
Supported aspect ratios	4:3, 16:10
Contrast ratio (typical)	2000:1
Screen size compatibility	27 - 300 \
Projector native resolution	WXGA (1280x800)
Keystone correction, vertical	± 40 °
Focus	Manual
Throw ratio	1.5 - 1.8:1
Focal length range	- mm
Lamp power	230 W
Light source type	Lamp
Service life of light source	4000 h
Service life of light source (economic mode)	6000 h
Full HD	No
Supported video modes	1080i, 1080p, 480i, 480p, 576i, 576p, 720p
Analog signal format system	NTSC, PAL, SECAM
RMS rated power	10 W
Number of built-in speakers	2
Serial interface type	RS-232
USB 2.0 ports quantity	0
S-Video inputs quantity	1
VGA (D-Sub) ports quantity	3
Cables included	VGA
HDCP	-
Noise level	34 dB
Certification	CB, WEEE, UL/cUL, FCC-B, ICES-003, IRAM, NOM, PSB, C-tick, EK, CE, TUV/GS, GOST-R, Hygienic, SASO UKrSEPRO, CCC
Noise level (economic mode)	29 dB
Power source	AC
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	1 W
Power consumption (typical)	305 W
Operating temperature (T-T)	0 - 40 °C
Product color	Black
Market positioning	Presentation
Sustainability certificates	RoHS

Weight and Dimensions

Depth	114 mm
Width	280 mm
Height	218 mm
Weight	1850 g
Package depth	305 mm
Package width	345 mm
Package height	220 mm
Package weight	4500 g