Example:
0x00,0xff,0xff,0xff,0xff,0xff,0xff,0x00,0x59,0x24,0x03,0x00,0x01,0x00,0x00,0x00,
0x05,0x19,0x01,0x03,0x80,0x3d,0x23,0x78,0x2a,0x5f,0xb1,0xa2,0x57,0x4f,0xa2,0x28,
0x0f,0x50,0x54,0xbf,0xef,0x80,0x71,0x40,0x81,0x00,0x81,0xc0,0x81,0x80,0x95,0x00,
0xa9,0xc0,0xb3,0x00,0xd1,0x00,0x04,0x74,0x00,0x30,0xf2,0x70,0x5a,0x80,0xb0,0x58,
0x8a,0x00,0x60,0x59,0x21,0x00,0x00,0x1e,0x00,0x00,0x00,0xfd,0x00,0x18,0x4b,0x1e,
0x5a,0x1e,0x00,0x0a,0x20,0x20,0x20,0x20,0x20,0x20,0x00,0x00,0x00,0xfc,0x00,0x47,
0x65,0x6e,0x65,0x72,0x69,0x63,0x5f,0x34,0x4b,0x0a,0x20,0x20,0x00,0x00,0x00,0xff,
0x00,0x30,0x0a,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x01,0x3f,
0x02,0x03,0x39,0xc3,0x4b,0x90,0x04,0x1f,0x13,0x03,0x12,0x20,0x0f,0x1e,0x24,0x26,
0x35,0x09,0x7f,0x04,0x0f,0x7f,0x04,0x15,0x07,0x50,0x3d,0x1f,0xc0,0x5f,0x54,0x01,
0x57,0x06,0x00,0x67,0x54,0x00,0x83,0x5f,0x00,0x00,0x6e,0x03,0x0c,0x00,0x10,0x00,
0x80,0x3c,0x20,0x10,0x80,0x01,0x02,0x03,0x04,0x02,0x3a,0x80,0xd0,0x72,0x38,0x2d,
0x40,0x10,0x2c,0x45,0x80,0x60,0x59,0x21,0x00,0x00,0x1e,0x01,0x1d,0x00,0x72,0x51,
0xd0,0x1e,0x20,0x6e,0x28,0x55,0x00,0x60,0x59,0x21,0x00,0x00,0x1e,0x02,0x3a,0x80,
0x18,0x71,0x38,0x2d,0x40,0x58,0x2c,0x45,0x00,0x60,0x59,0x21,0x00,0x00,0x1e,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x9d
3. Save the
*.edid
file.
4. Upload the EDID to the encoder.
5. Power cycle the encoder to use the new EDID file.
The source device may need to be power-cycled in order to accept the new EDID. Physically remove power from the source device
then reapply it.
CUSTOM SPLASH SCREEN (DECODER ONLY)
A custom splash screen may be uploaded to the decoder for use when there is no audio source, or a source time out occurs. The file
must be a JPEG (*.jpg) and be less than 500KB (524287 bytes) in size. Resolution should be 1920x1080. Other resolutions will
result in lower quality or aspect ratio mismatch.
ADVANCED CONFIGURATION
VIDEO SOURCE TIMEOUT (DECODER ONLY)
VIDEO.SOURCE_TIMEOUT
– When there is no source available, time out TRUE will cause the decoder to switch to the splash screen
after approximately 10 seconds.
VIDEO POWER SAVE (DECODER ONLY)
VIDEO.POWER_SAVE – After the time out, turn off the HDMI output.
HDCP FORCE ON
Encoder: Force the encoder to accept only HDCP sources.
Decoder: Force the decoder to HDCP encrypt the output.
HDCP Force On determines whether a unit forces HDCP for all sources or sinks (TRUE) or allows non-encrypted to go through natively
(FALSE). When FALSE switching can be slow if you need to renegotiate the HDMI link.
HDCP FORCE OFF (ENOCDER ONLY)
Tells the source device that the encoder will not accept HDCP encrypted content. It cannot be used to remove HDCP from sources.
GENLOCK (DECODER ONLY)
When set to FALSE allows the decoder output to free run and not be genlocked to the source encoder. Useful for some projectors
that cannot accommodate wide clock range. Should be set to TRUE for video wall setups.
To Next Page
Loading...
