What to do if Xantrex Freedom XC PRO AC output is overloaded?
If the Xantrex Battery Charger indicates an AC output overload shutdown, reduce the electrical loads connected to the unit's AC outlet. Also, inspect any connected appliances with high-surge ratings and disconnect them if necessary.
What to do if Xantrex Battery Charger shows over-temperature shutdown?
If the Xantrex Battery Charger displays an over-temperature shutdown, try the following: reduce the loads connected to the AC outlet, ensure that the ventilation grille is unblocked, and, if possible, move the unit to a cooler environment.
What to do if Xantrex Freedom XC PRO gives AC output overload warning?
If the Xantrex Battery Charger is giving an AC output overload warning, reduce the loads connected to the AC outlet of the unit.
What to do if Xantrex Freedom XC PRO shows over-temperature alarm and fan lock alarm?
If the Xantrex Battery Charger is showing an over-temperature alarm and a fan lock alarm, take these steps: reduce the loads connected to the AC outlet, make sure the ventilation grille isn't blocked, move the unit to a cooler place if you can, and check the fan for anything that might be stopping it from spinning, removing any obstructions.
Why Xantrex Freedom XC PRO Battery Charger shows high battery voltage shutdown?
If the Xantrex Battery Charger is experiencing a high battery voltage shutdown (above 18.0 volts DC), check for external charging sources like a PV charger or an over voltage alternator, and disconnect them if needed.
What to do if Xantrex Freedom XC PRO Battery Charger fan lock error occurs?
If the Xantrex Battery Charger displays a fan lock error, and there's nothing obviously wrong with the fan, try disconnecting the unit from both its DC and AC power sources, then reconnect and restart it. Perform Drip Shield Installation on page 47. If the error continues, contact customer service.
What to do if Xantrex Battery Charger battery temperature is high?
Error detection and automatic charger temperature compensation are enabled only when the optional BTS (PN: 808- 0232-01) is installed. When the BTS is present and the error is detected, stop inverting (meaning, discharging the battery) and wait a minimum of one hour for the battery temperature to go down before resuming inverting.
What to do if Xantrex Freedom XC PRO Battery Charger internal hardware error occurs?
If the Xantrex Battery Charger shows an internal hardware error that persists, contact customer service.
How to fix Xantrex Battery Charger low battery voltage shutdown?
If a low battery voltage shutdown is imminent on your Xantrex Battery Charger, check the battery status and recharge if needed. Also, verify the DC cable sizing is correct and tighten any loose connections.
General| Dimensions | Varies by model |
|---|---|
| Battery Type | Flooded, Gel, AGM, Lithium |
| Certifications | UL |
| Output Current | 30/50/60 A |
| Operating Temperature | -20°C to 50°C (-4°F to 122°F) |
Details FCC compliance and interference mitigation measures for the device.
Lists the components included in the Freedom XC PRO base package.
Highlights primary capabilities like power output, surge capacity, and transfer switch function.
Lists the default settings for the Freedom XC PRO system.
Details the AC/DC and GFCI panel components and features.
Explains the features and components of the display panel.
Describes the features and components of the side panel.
Provides guidance and safety precautions before starting the installation process.
Details governing installation codes for various applications like RV and marine.
Lists the necessary tools and materials required for the installation.
Outlines the main steps involved in the installation process.
Illustrates a typical marine installation with its components.
Provides instructions on how to install drip shields for unit protection.
Details the display panel, status LEDs, function buttons, LCD screen, and icons.
Explains operation, status indicators, and power-saving features in battery mode.
Covers battery charger functions, battery types, and charging algorithms.
Explains how the unit transitions between grid and battery power sources.
Guides users on how to adjust various feature settings in the configuration mode.
Provides guidance on periodic cleaning and checks for the inverter/charger unit.
Steps to take before contacting customer service for troubleshooting.
Lists warning messages, audible alarms, and error codes displayed on the LCD.
Provides a table of common problems, possible causes, and solutions.
Discusses inverter performance with different AC loads like resistive and motor loads.
Details the physical dimensions and weight of the inverter/charger models.
Lists the operating and storage temperature and humidity ranges.
Covers transfer relay rating, transfer times, transfer voltage, and cooling.
Lists safety and EMC compliance standards and certifications.
To Next Page