Xerox Versant 80 Press - Booklet Maker Finisher

Detailed Specifications Xerox
®
Versant® 80 Press
Customer Expectation and Installation Guide Xerox Confidential 18
Interposer
The Standard Finisher includes a standard Interposer (also called a Post-Process Inserter), used to insert preprinted stock into finished sets without having to go
through the engine. This tray, on the Press Control Panel is called Tray T1 (on some products it is Tray 8).
NOTE: Labels, coated media, and envelopes are not supported.
Interposer Capacity by weight and paper finish
Paper type and weight Paper Size
B5 / 8 x 10 in A4 / 8.5 x 11 in B4 / 8.5 x 14 in A3 / 11 x 17 in
Uncoated 52-80 gsm 200 sheets 200 sheets 200 sheets 200 sheets
81-220 gsm H=22 mm (0.87 in) H=22 mm (0.87 in) H=22 mm (0.87 in) H=22 mm (0.87 in)
Hole Punching
The Standard Finisher offers Hole Punching as a standard feature.
 Holes are created on the trail edge of the sheet.
 Hole punch capacity is equal to the regular capacity of the chosen output tray.
 For the USA, 2- and 3-hole punching is available; for Europe, 2- and 4- hole punch is available.
 Stacks can be punched on the left or right side, or on the top edge.
Hole Punch Capacity by weight and paper finish
Paper type and weight Paper Size
B5 A4 / 8.5 x 11 in B4 / 8.5 x 14 in A3 / 11 x 17 in
Uncoated 52-220 gsm Applicable Applicable Applicable Applicable
Coated 106-220 gsm Applicable Applicable Applicable Applicable
Standard Finisher Limitations
Productivity may be reduced by up to 50% when running multiple sets of a single sheet job to the Stacker Tray, due to
the press being forced to wait while each single sheet set is ejected to the Stacker Tray.
Booklet Maker Finisher
The Booklet Maker Finisher is a sepa
r
ate configu
r
ation that adds basic booklet making capability to all the same
f
eatures as the Standa
r
d Finisher. The Booklet
Maker Finisher includes:
 Hole Punch
 Stapler
 Top Tray
 Stacker Tray
 Booklet Unit capable of saddle stapling and bi-folding
NOTE: Hole punching is not available to the Booklet Tray
Booklet Maker Finisher
Specifications
For specifications on the Top Tray, Stacker Tray, Stapling, Hole Punching, and the Interposer refer to Standard Finisher
Specifications.
The following provides specifications on the Booklet Maker.
Booklet Capabilities by Weight and Paper Finish
Sheets per booklet by weight and paper finish
Paper type and weight Paper Size
A4 / 8.5 x 11 in B4 / 8.5 x 14 in A3 / 11 x 17 in 12 x 18 in SRA3
Uncoated 52-80 gsm 25 25 25 25 25
81-90 gsm 20 20 20 20 20
91-105 gsm 10 10 10 10 10
106-128 gsm 10 10 10 10 10
129-150 gsm 10 10 10 10 10
151-176 gsm 10 10 10 10 10
177-220 gsm 5 5 5 5 5
221-256 gsm 4 4 4 4 4
257-350 gsm 3 3 3 3 3
Coated 106-128 gsm 10 10 10 10 10
129-150 gsm 10 10 10 10 10
151-176 gsm 10 10 10 10 10
177-220 gsm 5 5 5 5 5
221-256 gsm 4 4 4 4 4
257-350 gsm 3 3 3 3 3
Fold Accuracy of the Inner Sheet
(Lead and Side Edges)
• Stapled: ≤1.5 mm
f
or A4 sheets, ≤2.0 mm
f
or other sizes
• Non-stapled: ≤1.5 mm