YASKAWA YASNAC 3000G

Mount
the
core,
which
is
holding
the
tape,
the inside
reel.
5.
-
Tension
arm
stoppers
The tension
arm
is
locked
on
the
tension
arm
stopper
when the
NC
tape
is
not
set
on
the
tape
reel.
on
Place
the
reel bail
on
the
reel-hub
matching
the
position
of
the
bail
groove
with
that
of
reel
lock
pawl.
Turn
the
lock
pawl
until
the
pawl
is
engaged
between
the
two
small
boss¬
es
on
the reel
bail.
The
right
tape
reel
is
properly
mounted
as
shown
in
Fig.
5.2.
3.4.
6.
•
8"
Tape
reels
8,f
Tape
reels
can
accomodate
590
feet
(180
m)
NC
tape.
•
Reel-hub
Reel
hub
is
used
to
mount
and
fix
the
tape
reel
at
the
reel
spindle.
7.
Draw
the
NC
tape
approximately
5
feet
(1.5
m).
Insert
the
NC
tape
into
the
tape
reader
through
the
guide
rollers,
tension
arm on
the
right
hand
side.
8.
Attach
the
NC
tape,
which
is
coming
out
of
the
tapeTeader,
to
the
left
reel
in
the
same
manner
described
in
steps
1
to
6.
fail
to
wind the
NC
tape
two
or
three
times
on
the
left
core
so
that
tape
does
not
loosen.
9.
Never
REEL
STOPPER
PIN
/
10.
Draw
the
tape
coming
out
of
the
tape
reader
over
the
guide
rollers
and
tension
arm
fol¬
lowing
the
instructions
in
the
instruction
plate
for
setting
tape.
REEL-HUB
LOCK
PAWL
REEL
SPINDLE
Fig.
5.
2.
3.2
Turn the
right
and
left
reels
so
that
each
ten¬
sion
arm
locates
at
the
center
of
the
guide
rollers and
the
tension
arm
stopper.
Fig,
5.2.3.
1
shows
the
NC
tape
properly
mounted
on
both
tape
reels.
11.
Instruction
plates
The instruction
plate
shows
that
the
proper
setting
of
the
tape
over
the
guide
rollers
and
tension
arms
.
12.
Turn
on
the
reel
motor
power
switches.
The
tension
arm
may
move
at
that
instant,
however,
it
will
immediately
stop.
To
mount
the
NC
tape,
proceed
as
follows.
1.
To
remove
the
right
reel,
turn
the
reel
lock
pawl
with
the
reel
held
until
it
is
caught
in
the
groove
in
reel
bail.
Then
remove
the
reel
bail,
tape
core,
and
inside reel
at
one
time.
See
Fig.
5.
2.
3.
3.
NOTES:
•
When
tape
reels
are
not
be
used,
turn
off
the
reel
motor
power
switch.
*
To
remove
the
tape
from
the
tape
reels,
pro¬
ceed
as
follows.
1
a.
Turn
off
the
reel
motor
power
switch.
b.
Remove the
tape
from
the
tension
arm.
c.
Push
up
the
tape-
bail
of
the
tape
reader.
When
the
reel
motor
power
switch
is
on,
do
not
turn
the
tape
reel
with
the
NC
tape
set.
2.
Wind the
NC
tape
on
the
removed
tape
core
manually
after
trapping
the
tape
end
in
the
core
notch.
If
the
core
without
groove
is
used,
fit
the
tape
end
to
the
core
with
<:ollophane~tape
.
3.
Match the
position
of
reel
stopper
pin
with
that
of
reel
lock
pawl
by
turning
the
pawl.
See
Fig.
5.2.
3.
2.
4.
Set
the
inside
reel
on
the
reel-hub
matching
the
position
of
the
bail
groove
with
that
of
hub
lock
pawl.
-
123
-