Yealink SIP-T41S Administrator's Guide

Administrator’s Guide for SIP-T2 Series/T4 Series/T5 Series/CP920 IP Phones
391
Description
It enables or disables the DND feature synchronization for account X.
Note: The value configured by this parameter takes precedence over that configured by the parameter
"features.dnd.feature_key_sync.enable". It works only if “account.X.feature_key_sync.enable” is set to
1 (Enabled).
Permitted
Values
0-Disabled
1-Enabled, server-based DND is enabled. Server and local phone DND are synchronized.
Default
Blank
Supported
Devices
All phones except T48G, T46G, T42G, T41P, T29G and CP920
Parameter
features.dnd.feature_key_sync.local_processing.enable <y0000000000xx>.cfg
Description
It enables or disables the local DND when DND feature synchronization is enabled.
Note: It works only if “features.feature_key_sync.enable” and “features.dnd.feature_key_sync.enable”
are set to 1 (Enabled). The value configured by the parameter “account.X.features.dnd.feature_key_
sync.local_processing.enable” takes precedence over that configured by this parameter.
Permitted
Values
0-Disabled, DND is performed on the server side only.
1-Enabled, DND is performed on both the server side and locally.
Default
0
Parameter
account.X.features.dnd.feature_key_sync.local_processing.enable
[1]
<MAC>.cfg
Description
It enables or disables the local DND when DND feature synchronization is enabled.
Note: It works only if “features.feature_key_sync.enable” and “features.dnd.feature_key_sync.enable”
are set to 1 (Enabled).
Permitted
Values
0-Disabled, DND is performed on the server side only.
1-Enabled, DND is performed on both the server side and locally.
Default
Blank
[1]
X is the account ID. For T57W/T54W/T48U/T48S/T48G/T46U/T46S/T46G/T29G, X=1-16; for
T53W/T53/T43U/T42U/T42G/T42S, X=1-12; for T41P/T41S/T27G, X=1-6; for T40P/T40G/T23P/T23G, X=1-3; for T21
(P) E2, X=1-2.
Multiple Call Appearances
You can enable each registered line to support multiple concurrent calls. For example, you can place one call on
hold, switch to another call on the same registered line, and have both calls displayed.
You can set the maximum number of concurrent calls per line key on all-lines basis or a per-line basis. For
example, if you specify 3 concurrent-calls for account 1, you can only have three call appearances on a cor-
responding line key. The additional incoming calls will be rejected.
Note: The number of concurrent calls applies to all line keys. For example, if three line keys are associated with an account,
you can have three call appearances per line key.
Topic
Multiple Call Appearances Configuration
Multiple Call Appearances Configuration
You can specify the maximum concurrent calls per line key.
The following table lists the parameters you can use to configure multiple call appearances.

Yealink SIP-T41S Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Black
Keypad illumination	Yes
Wi-Fi	No
Networking standards	IEEE 802.3af
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet LAN interface type	Fast Ethernet
Supported network protocols	SIP v1, SIP v2, LLDP/CDP/DHCP, OpenVPN, IEEE802.1X, IPv6, FTP/TFTP/HTTP/HTTPS
Volume control	Digital
Number of programmable keys	6
Lines quantity	6 lines
Phonebook capacity	1000 entries
Dual-Tone Multi-Frequency (DTMF) modes	In-band, Out-of band, SIP info
Input frequency	50/60 Hz
AC adapter input voltage	100 - 240 V
AC adapter output current	1.2 A
AC adapter output voltage	5 V
Display diagonal	2.7 \
Display resolution	192 x 64 pixels
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 95 %
Voice codecs	CNG, G.711Mu, G.711a, G.723.1, G.726, G.729ab, VAD, iLBC
Certification	CE
Cables included	LAN (RJ-45)
Number of handles included	1 pc(s)
Harmonized System (HS) code	85171800

Weight and Dimensions

Depth	189 mm
Width	212 mm
Height	175 mm
Package depth	223 mm
Package width	246 mm
Package height	120 mm