EasyManuals Logo

Yealink SIP-T41S Administrator's Guide

Yealink SIP-T41S
572 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #549 background imageLoading...
Page #549 background image
Troubleshooting Methods
546
Ethernet Software Capturing Configuration
You can choose to capture the packets using the Ethernet software in two ways:
l Receiving data packets from the hub: Connect the Internet port of the IP phone and the PC to the same hub, and
then use Sniffer, Ethereal or Wireshark software to capture the signal traffic.
l Receiving data packets from PC port: Connect the Internet port of the IP phone to the Internet and the PC port of
the IP phone to a PC. Before capturing the signal traffic, make sure the phone can span data packets received
from the Internet port to the PC port. It is not applicable to CP920 phones.
Topic
Span to PC Port Configuration
Span to PC Port Configuration
The following table lists the parameter you can use to configure span to PC port.
Parameter
static.network.span_to_pc_port
[1]
<y0000000000xx>.cfg
Description
It enables or disables the phone to span data packets received from the WAN port to the PC port.
Note: It works only if “static.network.pc_port.enable” is set to 1 (Auto Negotiation).
Permitted
Values
0-Disabled
1-Enabled, all data packets from the Internet port can be received by PC port.
Default
0
Supported
Devices
All phones except CP920
Web UI
Network > Advanced > Span to PC > Span to PC Port
[1]
If you change this parameter, the phone will reboot to make the change take effect.
Watch Dog
The IP phone provides a troubleshooting feature called “Watch Dog”, which helps you monitor the IP phone status
and provides the ability to get stack traces from the last time the IP phone failed. If the Watch Dog feature is
enabled, the phone will automatically reboot when it detects a fatal failure. This feature can be configured using the
configuration files or via the web user interface.
Topic
Watch Dog Configuration

Table of Contents

Other manuals for Yealink SIP-T41S

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Yealink SIP-T41S and is the answer not in the manual?

Yealink SIP-T41S Specifications

General IconGeneral
MountingDesk/Wall
Handset typeWired handset
Product typeIP Phone
Product colorBlack
Keypad illuminationYes
Wi-FiNo
Networking standardsIEEE 802.3af
Ethernet LAN data rates10, 100 Mbit/s
Ethernet LAN interface typeFast Ethernet
Supported network protocolsSIP v1, SIP v2, LLDP/CDP/DHCP, OpenVPN, IEEE802.1X, IPv6, FTP/TFTP/HTTP/HTTPS
Volume controlDigital
Number of programmable keys6
Lines quantity6 lines
Phonebook capacity1000 entries
Dual-Tone Multi-Frequency (DTMF) modesIn-band, Out-of band, SIP info
Input frequency50/60 Hz
AC adapter input voltage100 - 240 V
AC adapter output current1.2 A
AC adapter output voltage5 V
Display diagonal2.7 \
Display resolution192 x 64 pixels
Operating temperature (T-T)-10 - 50 °C
Operating relative humidity (H-H)10 - 95 %
Voice codecsCNG, G.711Mu, G.711a, G.723.1, G.726, G.729ab, VAD, iLBC
CertificationCE
Cables includedLAN (RJ-45)
Number of handles included1 pc(s)
Harmonized System (HS) code85171800
Weight and Dimensions IconWeight and Dimensions
Depth189 mm
Width212 mm
Height175 mm
Package depth223 mm
Package width246 mm
Package height120 mm

Related product manuals