EasyManuals Logo

Yealink SIP-T48U Administrator's Guide

Yealink SIP-T48U
572 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #307 background imageLoading...
Page #307 background image
Account Settings
304
DNSTTL on the registered server expires, the phone will retry to send requests to the primary server.
2-Registration: the phone will send requests to the last registered server first. If the registration
expires, the phone will retry to send requests to the primary server.
3-duration: the phone will send requests to the last registered server first. If the time defined by the
“account.X.sip_server.Y.failback_timeout” parameter expires, the phone will retry to send requests to
the primary server.
Default
0
Parameter
account.X.sip_server.Y.failback_timeout
[1][2]
<MAC>.cfg
Description
It configures the timeout (in seconds) for the phone to retry to send requests to the primary server after
failing over to the current working server.
If you set the parameter to 0, the phone will not send requests to the primary server until a failover
event occurs with the current working server.
If you set the parameter between 1 and 59, the timeout will be 60 seconds.
Note: It works only if “account.X.sip_server.Y.failback_mode” is set to 3 (duration).
Permitted
Values
0, Integer from 60 to 65535
Default
3600
Parameter
account.X.sip_server.Y.failback_subscribe.enable
[1][2]
<MAC>.cfg
Description
It enables or disables the phone to retry to re-subscribe after registering to the secondary server with
different IP addresses when encountering a failover.
Note: It works only if "account.X.sip_server.Y.failback_mode" is set to 1, 2 or 3.
Permitted
Values
0-Disabled
1-Enabled, the phone will immediately re-subscribe to the secondary server, for ensuring the normal
use of the features associated with the subscription (for example, BLF, SCA).
Default
0
Parameter
account.X.outbound_proxy.Y.register_on_enable
[1][2]
<MAC>.cfg
Description
It enables or disables the phone to register to the secondary outbound proxy server before sending
requests to it when encountering a failover.
Permitted
Values
0-Disabled, the phone will not attempt to register to the secondary outbound proxy server, since the
phone assumes that the primary and secondary outbound proxy servers share registration inform-
ation. So the phone will directly send the requests to the secondary outbound proxy server.
1-Enabled, the phone will register to the secondary outbound proxy server first, and then send the
requests to it.
Default -1, the phone will invoke “account.X.sip_server.Y.register_on_enable to take effect.
Parameter
account.X.outbound_proxy.Y.retry_counts
[1][2]
<MAC>.cfg
Description
It configures the retry times for the phone to resend requests when the outbound proxy server Y is
unavailable or there is no response from the outbound proxy server Y.
The phone moves to the next available outbound proxy server after three failed attempts.
Permitted
Values
Integer from 0 to 20
Default -1, the phone will invoke “account.X.sip_server.Y.retry_counts” to take effect.
Parameter
account.X.outbound_proxy.Y.only_signal_with_registered
[1][2]
<MAC>.cfg

Table of Contents

Other manuals for Yealink SIP-T48U

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Yealink SIP-T48U and is the answer not in the manual?

Yealink SIP-T48U Specifications

General IconGeneral
Handset typeWired handset
Product typeIP Phone
Product colorGray
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Expansion module supportYes
Ethernet LAN (RJ-45) ports2
Display diagonal7 \
Display resolution800 x 480 pixels
Lines quantity- lines
Phonebook capacity1000 entries
Number of VoIP accounts16
Voice codecsAGC, AJB, AMR-WB, CNG, G.711, G.722, G.723.1, G.726, G.729ab, VAD, iLBC
Security algorithmsAES, HTTPS, SRTP, TLS
Ethernet LAN data rates10, 100, 1000 Mbit/s
Ethernet LAN interface typeGigabit Ethernet
Front camera-
AC adapter input voltage100 - 240 V
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)10 - 95 %
Keypad number of keys29
Number of handles included1 pc(s)
Harmonized System (HS) code85171800
Weight and Dimensions IconWeight and Dimensions
Width226 mm
Height185 mm

Related product manuals