EasyManuals Logo

Yealink SIP-T48U Administrator's Guide

Yealink SIP-T48U
572 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #39 background imageLoading...
Page #39 background image
Administrator’s Guide for SIP-T2 Series/T4 Series/T5 Series/CP920 IP Phones
36
Web UI
Network > Advanced > LLDP > Packet Interval (1~3600s)
Phone UI
Color Screen Phones:
Menu > Advanced (default password: admin) > Network > LLDP > Packet Interval
Black-and-white Screen Phones:
Menu > Settings > Advanced Settings (default password: admin) > Network > LLDP > Packet Interval
[1]
If you change this parameter, the phone will reboot to make the change take effect.
CDP Configuration
CDP (Cisco Discovery Protocol) allows the phones to receive and/or transmit device-related information from/to dir-
ectly connected devices on the local network.
When CDP feature is enabled on the phones, the phones periodically advertise their own information to the directly
connected CDP-enabled switch. The phones can also receive CDP packets from the connected switch and obtain
their VLAN IDs.
The following table lists the parameters you can use to configure CDP.
Parameter
static.network.cdp.enable
[1]
<y0000000000xx>.cfg
Description
It enables or disables the CDP feature.
Permitted
Values
0-Disabled
1-Enabled, the phone attempts to determine its VLAN ID through CDP.
Default
1
Web UI
Network > Advanced > CDP > Active
Phone UI
Color Screen Phones:
Menu > Advanced (default password: admin) > Network > CDP > CDP Status
Black-and-white Screen Phones:
Menu > Settings > Advanced Settings (default password: admin) > Network > CDP > CDP Status
Parameter
static.network.cdp.packet_interval
[1]
<y0000000000xx>.cfg
Description
It configures the interval (in seconds) that how often the phone sends the CDP request.
Note: It works only if “static.network.cdp.enable is set to 1 (Enabled).
Permitted
Values
Integer from 1 to 3600
Default
60
Web UI
Network > Advanced > CDP > Packet Interval (1~3600s)
Phone UI
Color Screen Phones:
Menu > Advanced (default password: admin) > Network > CDP > CDP Interval
Black-and-white Screen Phones:
Menu > Settings > Advanced Settings (default password: admin) > Network > CDP > CDP Interval
[1]
If you change this parameter, the phone will reboot to make the change take effect.

Table of Contents

Other manuals for Yealink SIP-T48U

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Yealink SIP-T48U and is the answer not in the manual?

Yealink SIP-T48U Specifications

General IconGeneral
Handset typeWired handset
Product typeIP Phone
Product colorGray
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Expansion module supportYes
Ethernet LAN (RJ-45) ports2
Display diagonal7 \
Display resolution800 x 480 pixels
Lines quantity- lines
Phonebook capacity1000 entries
Number of VoIP accounts16
Voice codecsAGC, AJB, AMR-WB, CNG, G.711, G.722, G.723.1, G.726, G.729ab, VAD, iLBC
Security algorithmsAES, HTTPS, SRTP, TLS
Ethernet LAN data rates10, 100, 1000 Mbit/s
Ethernet LAN interface typeGigabit Ethernet
Front camera-
AC adapter input voltage100 - 240 V
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)10 - 95 %
Keypad number of keys29
Number of handles included1 pc(s)
Harmonized System (HS) code85171800
Weight and Dimensions IconWeight and Dimensions
Width226 mm
Height185 mm

Related product manuals