YOKOGAWA DL1640 User Manual

1-29
IM 701610-61E
1
I
2
C-Bus Signal Analysis Function
Command Function Page
:SEARch:I2C:ANALyze:SETup:CLOCk:HYSTeresis
Sets the clock channel hysteresis of the I
2
C analysis condition or queries
the current setting. 1-35
:SEARch:I2C:ANALyze:SETup:CLOCk:LEVel
Sets the clock channel level of the I
2
C analysis condition or queries the
current setting. 1-36
:SEARch:I2C:ANALyze:SETup:CLOCk:SOURce
Sets the clock channel source waveform of the I
2
C analysis condition or
queries the current setting. 1-36
:SEARch:I2C:ANALyze:SETup:DATA? Queries all settings related to the data channel of the I
2
C analysis
condition. 1-36
:SEARch:I2C:ANALyze:SETup:DATA:LEVel
Sets the data channel threshold level of the I
2
C analysis condition or
queries the current setting. 1-36
:SEARch:I2C:ANALyze:SETup:DATA:SOURce
Sets the data channel source waveform of the I
2
C analysis condition or
queries the current setting. 1-36
:SEARch:I2C:ANALyze:SETup:MPOSition Sets the reference position when the I
2
C reference position is set to
manual or queries the current setting. 1-36
:SEARch:I2C:ANALyze:SETup:RPOint Sets the reference position when the I
2
C reference position is set to
manual or queries the current setting. 1-36
:SEARch:I2C:LIST? {<NRf>} Outputs one byte of I
2
C analysis result as a character string. 1-36
:SEARch:I2C:SEARch? Queries all settings related to the I
2
C analysis result search. 1-37
:SEARch:I2C:SEARch:ADDRess? Queries all settings related to the Address search of the I
2
C analysis
result. 1-37
:SEARch:I2C:SEARch:ADDRess:ACK Sets the Ack condition of the Address search of the I
2
C analysis result or
queries the current setting. 1-37
:SEARch:I2C:SEARch:ADDRess:HEXa Sets the searched Address pattern of the I
2
C analysis result in
hexadecimal. 1-37
:SEARch:I2C:SEARch:ADDRess:MODE Sets the valid/invalid setting of the Address pattern when searching the
I
2
C analysis result or queries the current setting. 1-37
:SEARch:I2C:SEARch:ADDRess:PATTern Sets the searched Address pattern of the I
2
C analysis result in binary or
queries the current setting. 1-37
:SEARch:I2C:SEARch:DATA? Queries all settings related to the Data search of the I
2
C analysis result. 1-37
:SEARch:I2C:SEARch:DATA:ACK Sets the Ack condition of the Data search of the I
2
C analysis result or
queries the current setting. 1-37
:SEARch:I2C:SEARch:DATA:HEXa Sets the searched Data pattern of the I
2
C analysis result in hexadecimal. 1-37
:SEARch:I2C:SEARch:DATA:MODE Sets the valid/invalid setting of the Data pattern when searching the
I
2
C analysis result or queries the current setting. 1-37
:SEARch:I2C:SEARch:DATA:PATTern Sets the searched Data pattern of the I
2
C analysis result in binary or
queries the current setting. 1-38
:SEARch:I2C:SEARch:NEXT? Performs the I
2
C analysis result search after the current byte and returns
the search position. 1-38
:SEARch:I2C:SEARch:PREVious? Performs the I
2
C analysis result search before the current byte and
returns the search position. 1-38
:SEARch:I2C:SEARch:TYPE Sets the type of I
2
C analysis result search or queries the current setting. 1-38
:SEARch:TYPE Sets the search type or queries the current setting. 1-38
I
2
C File Group
:FILE:SAVE:I2C[:EXECute] Executes the save operation of the I
2
C analysis result.
This is an overlap command. 1-38
:FILE:SAVE:I2C:ABORt Aborts the save operation of the I
2
C analysis result. 1-38
1.7 Communication Commands

YOKOGAWA DL1640 Specifications

General

Brand	YOKOGAWA
Model	DL1640
Category	Test Equipment
Language	English