Operation Manual / 4 Product description / A100-L
Figures
© Copyright 2020 ABB. All rights reserved. HZTL4034_EN Revision R October 2020
Figures
Fig.1: Layout and function of the turbocharger....... 5
Fig.2: Warning plate locations ..................................... 7
Fig.3: Locations of the rating plates ......................... 8
Fig.4: Fitting the lifting gear...................................... 10
Fig.5: Placing the turbocharger................................. 11
Fig.6: Compressor-end foot....................................... 12
Fig.7: Turbine-end foot................................................ 12
Fig.8: Oil temperature at the outlet.......................... 18
Fig.9: Layout and overview of the speed measure-
ment system.................................................................. 20
Fig.10: Replacing the speed sensor .......................... 22
Fig.11: U-tube manometer at the filter silencer...... 23
Fig.12: Noise insulation, bellows .............................. 25
Fig.13: Layout and overview of filter silencer ......... 33
Fig.14: Dismantling filter ring circumferential part....
35
Fig.15: Opening filter ring lock.................................. 35
Fig.16: Attaching new filter ring ............................... 36
Fig.17: Fitting new filter ring ..................................... 36
Fig.18: Overview of wet cleaning of compressor.. 39
Fig.19: Filter plug view................................................ 40
Fig.20: Overview of dry cleaning device.................. 42
Fig.21: Drain pipe diagram......................................... 45
Fig.22: Weights of assemblies ................................. 54
Fig.23: Dismantling the filter silencer casing ........ 55
Fig.24: Fitting the filter silencer casing .................. 56
Fig.25: Fitting the filter silencer casing .................. 57
Fig.26: Fitting the filter silencer casing .................. 57
Fig.27: Fitting the filter silencer casing .................. 58
Fig.28: Fitting the filter silencer casing .................. 58
Fig.29: Fitting the bellows ......................................... 59
Fig.30: Dismantling the filter silencer ..................... 60
Fig.31: Dismantling the filter silencer....................... 61
Fig.32: Dismantling the filter silencer with noise
package ........................................................................... 62
Fig.33: Dismantling the wall insert............................ 63
Fig.34: Moving out wall insert .................................... 64
Fig.35: Putting down wall insert ................................ 64
Fig.36: Putting down wall insert ................................ 65
Fig.37: Dismantling the diffuser ............................... 66
Fig.38: Measuring axial clearance A .......................... 67
Fig.39: Removing the insulation (A175-L and smal-
ler)..................................................................................... 68
Fig.40: Dismantling the gas inlet casing (A175-L and
smaller) ............................................................................ 69
Fig.41: Dismantling the nozzle ring (A175-L and
smaller) ............................................................................ 70
Fig.42: Dismantling the gas inlet casing (180-L and
larger)................................................................................ 71
Fig.43: Fitting the nozzle ring holder........................ 72
Fig.44: Dismantling the nozzle ring .......................... 73
Fig.45: Put down the nozzle ring ............................... 73
Fig.46: Fitting the nozzle ring (A175-L and smaller) ...
74
Fig.47: Fitting the gas outlet casing (A175-L and
smaller) ............................................................................ 75
Fig.48: Fitting the insulation (A175-L and smaller) 76
Fig.49: Looping around the nozzle ring (A180-L and
larger)............................................................................... 77
Fig.50: Fitting the nozzle ring (A180-L and larger) 78
Fig.51: Fitting the gas inlet casing (A180-L and lar-
ger) ................................................................................... 79
Fig.52: Measuring axial clearance A .......................... 80
Fig.53: Fitting the diffuser.......................................... 81
Fig.54: Positioning wall insert.................................... 82
Fig.55: Fitting wall insert ............................................ 83
Fig.56: Fitting the filter silencer ................................ 85
Fig.57: Fitting the filter silencer................................. 86
Fig.58: Fitting the filter silencer with noise package.
87
Fig.59: Overview of tightening torques ................... 89
Page 108 / 110Page 108 / 110
To Next Page
Loading...
