AQUAMASTER4 | ELECTROMAGNETIC FLOWMETER TRANSMITTER | OI/FET400-EN REV. D 51
Device Information Description
Note
Transmitter unique ID Transmitter-specific
Read-only
Transmitter serial number Transmitter-specific
Read-only
Transmitter date of manufacture Date and time of transmitter manufacture
Read-only
Sensor unique ID Sensor-specific
Read-only
Sensor serial number Sensor-specific
Read-only
Sensor date of manufacture Date and time of sensor manufacture
Read-only
Transmitter build type Factory set. Options: Integral sensor/Remote sensor
Read-only
Meter tag Used to enter a unique tag for the meter
Editable
Meter owner Used to enter the owner of the meter
Editable
Transmitter location Used to enter the location of the transmitter
Editable
Sensor location Used to enter the location of the sensor
Editable
Sensor type Type of sensor. Types: Full bore/Probe
Read-only
Calibration accuracy Options: Normal/Class 1/Class 2/MID Class 1/MID Class 2
Read-only
Sensor certificate number Sensor-specific
Read-only
MID switch state The position of the MID lock switch. Options: Locked/Unlocked/Not fitted
Read-only
Lining material The lining material of the meter
Read-only
Electrode material The electrode material of the meter
Read-only
Flange material The flange material of the meter
Read-only
Calendar date/time Used to set the device date (format DD/MM/YYYY) and time (format hr/min/sec). A prompt is displayed
if the set date/time differs from the device.
Editable
Time zone*
Time zone adjustment configurations. Options: UTC-12:00 | UTC-11:00 | UTC-10:00 | UTC-9:30 | UTC-
0:00 | UTC-8:00 | UTC-7:00 | UTC-6:00 | UTC-5:00 | UTC-4:00 | UTC-3:30 | UTC-3:00 | UTC-2:00 | UTC-1:00 |
UTC | UTC+1:00 | UTC+2:00 | UTC+3:00 | UTC+3:30 | UTC+4:00 | UTC+4:30 | UTC+5:00 | UTC+5:30 |
UTC+5:45 | UTC+6:00 | UTC+6:30 | UTC+7:00 | UTC+8:00 | UTC+8:45 | UTC+9:00 | UTC+9:30 | UTC+10:00 |
UTC+10:30 | UTC+11:00 | UTC+12:00 | UTC+12:45 | UTC+13:00 | UTC+14:00
Editable
Daylight saving* Used to set daylight saving mode. Options: On | Off
Editable
Sensor and Connection Type The status of the connector sensor. Options: Integral sensor/VKG sensor connected/VKG sensor
disconnected
Read-only
Transmitter firmware checksum The checksum of the firmware in the transmitter (FEX41X/43X)
Read-only
Top Line User Decimal Used to set the decimal place for the totalizer
Editable
Display Settings Description Note
Velocity Used to select if the velocity is displayed on the transmitter Editable
Flow rate Used to select if the flow value is displayed on the transmitter Editable
Pressure If the option is ordered, used to select if pressure is displayed on the transmitter Editable
Forward Totalizer Used to select if the forward flow total is displayed on the transmitter Editable
Reverse Totalizer Used to select if the reverse flow total is displayed on the transmitter Editable
Net Totalizer Used to select if the net total flow is displayed on the transmitter Editable
Display Test Used to test the display of the transmitter Editable
Top line leading zeros Used to set the leading zeros for the totalizer Editable
Process Logger Settings
*
Description Note
Logging interval Used to enter interval time in seconds between logging of process values Editable
Retrieved record interval Used to enter interval time in seconds between data capture when retrieving process values Editable
* Available with FEX45X only.
To Next Page
Loading...
