Why won't my ABB Laboratory Equipment Master Controller or Ovens power on?
If the Master Controller or Ovens do not power on, check for power-related problems. This includes examining the external power supply, fuses, and breaker boxes for any potential issues.
Troubleshooting power-related issues with the Master Controller and ovens.
Steps for identifying and troubleshooting issues based on status indicators.
Categorized troubleshooting for operational issues like baseline noise and offsets.
Troubleshooting causes and symptoms of baseline noise in the detector signal.
Identifying and correcting baseline offsets due to incorrect temperatures or gas issues.
Troubleshooting scenarios where no peaks are detected in the analysis.
Troubleshooting the flame out LED and ignition failures.
Procedures for software repair and system recovery using USB flash drives.
Options for creating restore points and managing chromatogram data files.
Diagnosing and resolving issues where the DID plasma fails to ignite.
Troubleshooting low or no signal output from the DID detector.
Identifying causes for low signal output from the DID, such as restrictors or bias voltage.
Troubleshooting causes of noisy signals in the DID detector, including connections and leaks.
Diagnosing and resolving high baseline issues in HID mode, related to gas quality or leaks.
Troubleshooting causes of baseline drift, including pressure control and column bleed.
Identifying causes of signal spikes, such as loose connections or unstable bias voltage.
Procedure for replacing the EPC Control PCB in Class B and Class C ovens.
Procedure for removing a sensor PCB from the EPC control assembly.
Procedure for installing a new sensor PCB into the EPC control assembly.
Procedure for removing a proportional valve from the EPC control assembly.
Procedure for installing a new proportional valve into the EPC control assembly.
Procedure for removing the control PCB from the EPC enclosure.
Procedure for installing a new control PCB into the EPC enclosure.
Procedure for removing the heater from the EPC control assembly.
Procedure for installing a new heater into the EPC control assembly.
Instructions for removing and replacing the FID Amplifier Assembly.
Instructions for removing and replacing the FPD Electrometer.
Instructions for removing and replacing the TCD Amplifier Assembly.
Procedure for replacing the DTC Analog PCB (version 1).
Procedure for replacing the DTC Digital PCB (version 1).
Procedure for replacing the DTC Master Analog board (version 2).
Procedure for replacing the DTC Digital PCB (version 2).
Procedures for removing, installing, and cutting columns.
Instructions for repairing components of the Flame Ionization Detector (FID).
Procedure for replacing the thermocouple assembly in the FID detector.
Procedure for replacing the polarizer assembly in the FID detector.
Procedure for replacing the igniter assembly in the FID detector.
Instructions for repairing the Single Port Thermal Conductivity Detector (TCD).
Procedure for installing new filaments in the single port TCD.
Instructions for repairing the Multiport Thermal Conductivity Detector (TCD).
Procedure for removing filaments from the multiport TCD.
Procedure for installing new filaments in the multiport TCD.
Instructions for repairing components of the Flame Photometric Detector (FPD).
Procedure for replacing the photomultiplier assembly in the FPD.
Procedure for removing and installing the burner block in the FPD.
Instructions for repairing the Liquid Sample Valve (LSV).
Step-by-step guide for disassembling the LSV on the analyzer.
Instructions for repairing CP valves, including slider, wedges, and O-rings.
Instructions for replacing diaphragm valves, including four and one screw types.
Instructions for replacing components of the Optional Discharge Ionization Detector (DID).
List of common interior components for both Class B oven versions.
General| Analyzer Platform | PGC5000 |
|---|---|
| Technology | Gas Chromatography |
| Hazardous Area | ATEX, IECEx |
| Communication | Modbus |
| Measurement Principle | Gas Chromatography |
| Response Time | 30 seconds |
| Output Signal | 4-20 mA |
| Power Supply | 24 VDC or 100-240 VAC |
| Operating Temperature | -20°C to +55°C |
| Enclosure Rating | IP66 |
To Next Page
