ABB Relion 620 Series

To Next Page

To Previous Page

A071162 V1 EN

Figure 81: Selecting TCP/IP protocol

4. Choose Use the following IP address. Enter an IP address and a subnet mask. Make

sure that the IP address is unique, that is not used by any other device on the network.

1MAC456939-IB D Section 8

Commissioning

620 series ANSI 119

Operation Manual

Main Page

Table of Contents9
Section 1 Introduction15
This Manual15
Intended Audience15
Product Documentation16
Product Documentation Set16
Document Revision History16
Related Documentation17
Symbols and Conventions17
Symbols17
Document Conventions18
Functions, Codes and Symbols18
Section 2 Environmental Aspects25
Sustainable Development25
Disposal of a Protection Relay25
Section 3 620 Series Overview27
Overview27
Local HMI27
Display28
Leds30
Keypad30
Programmable Push Buttons with Leds33
Local HMI Functionality34
Protection and Alarm Indication34
Parameter Management36
Front Communication36
Web HMI37
Command Buttons38
Authorization39
Audit Trail39
Communication42
Self-Healing Ethernet Ring43
Ethernet Redundancy44
PCM600 Tool46
Connectivity Packages47
PCM600 and Relay Connectivity Package Version47
Section 4 Using the HMI49
Using the Local HMI49
Logging in49
Logging out50
Turning the Display Backlight on51
Selecting Local or Remote Use51
Identifying the Device52
Adjusting the Display Contrast53
Changing the Local HMI Language54
Changing Display Symbols54
Navigating in the Menu55
Menu Structure55
Scrolling the Display55
Changing the Default View56
Viewing Single-Line Diagram56
Changing Single-Line Diagram Symbol Formats57
Browsing Setting Values58
Editing Values59
Editing Numerical Values59
Editing String Values61
Editing Enumerated Values61
Committing Settings61
Clearing and Acknowledging62
Using the Local HMI Help63
Using the Web HMI63
Logging in64
Logging out64
Identifying Device65
Navigating in Menus66
Menu Structure67
Selecting Single-Line Diagram67
Showing Parameters68
Editing Values69
Committing Settings71
Clearing and Acknowledging73
Selecting Programmable Leds View74
Selecting Event View74
Selecting DFR Records View75
Uploading DFR Records76
Triggering DFR Recorder Manually77
Deleting DFR Records78
Selecting Phasor Diagrams79
Selecting Fault Records82
Using Web HMI Help83
Section 5 Protection Relay Operation85
Normal Operation85
Disturbance Identification85
DFR Recording Triggering86
DFR Record Analysis86
DFR Reports86
Relay Self-Supervision87
Relay Parametrization87
Settings for Relay Functionality87
Settings for Different Operating Conditions88
Section 6 Operating Procedures89
Monitoring89
Indications89
Monitoring Indication Messages89
Monitoring an Internal Relay Fault90
Monitoring Condition Monitoring Data90
Measured and Calculated Values90
Measured Values90
Using the Local HMI for Monitoring93
Recorded Data93
Creating Digital Fault Records93
Monitoring DFR Data94
Controlling and Uploading of DFR Recorder Data95
Monitoring Fault Records95
Monitoring Events96
Monitoring and Uploading Load Profile Record97
Remote Monitoring97
Monitoring Protection Relays Remotely97
Controlling97
Controlling with Single-Line Diagram97
Controlling Circuit Breaker, Disconnectors and Earthing Switch97
Controlling SLD Buttons98
Controlling Via the Control Menu99
Resetting Protection Relays101
Clearing and Acknowledging Via the Local HMI101
Changing the Protection Relay Functionality102
Defining the Setting Group102
Activating a Setting Group102
Copying a Setting Group103
Browsing and Editing Setting Group Values104
Activating Programmable Leds106
Setting Autoscroll Delay106
Section 7 Troubleshooting109
Fault Tracing109
Identifying Hardware Errors109
Identifying Runtime Errors109
Identifying Communication Errors109
Checking Front Communication Link Operation110
Checking Time Synchronization110
Running the Display Test110
Indication Messages110
Internal Faults110
Warnings113
Correction Procedures115
Rebooting the Software115
Restoring Factory Settings115
Setting Passwords116
Identifying Relay Application Problems116
Inspecting Wiring117
Sample Data Interruptions117
Section 8 Commissioning119
Commissioning Checklist119
Checking the Installation120
Checking of the Power Supply120
Checking CT Circuits120
Checking VT Circuits121
Checking Binary Input and Output Circuits121
Checking Binary Input Circuits121
Checking Binary Output Circuits122
Checking Optical Connections122
Authorizations122
User Authorization122
Using PCM600123
Setting the Communication between Protection Relays and PCM600115123
Communication Link Options between PCM600 and Protection124
Relays124
Setting Communication Parameters124
Setting Protection Relay and Communication129
Communication Settings129
Serial Communication Ports and Drivers130
Serial Link Diagnostics and Monitoring131
Defining Ethernet Port Settings134
Defining Serial Port Settings134
Setting Communication Protocol Parameters134
Connecting Jumper Connectors135
Communication Checklist135
Setting the Local HMI136
Changing the Local HMI Language136
Adjusting the Display Contrast136
Changing Display Symbols137
Changing the Default View137
Setting the System Time and Time Synchronization137
Setting Protection Relay Parameters139
Defining Setting Groups139
Relay Parametrization142
Defining DFR Channel Settings143
Configuring Analog Inputs143
Testing Protection Relay Operation143
Selecting the Test Mode144
Testing the Digital I/O Interface144
Testing Functions145
Selecting the Internal Fault Test145
ABB Product Data Registration146
Section 9 Glossary147

ABB Relion 620 Series - Page 127

Table of Contents

Other manuals for ABB Relion 620 Series

Related product manuals