To Next PageTo Next Page
Need help?Do you have a question about the Agilent Technologies 83620A and is the answer not in the manual?
General| Brand | Agilent Technologies |
|---|---|
| Model | 83620A |
| Category | Blower |
| Language | English |
Essential safety precautions for servicing, including electrical shock warnings and proper grounding.
Instructions for verifying configuration and using an autotransformer before powering on the instrument.
Defines the representation of physical keys on the instrument's front panel.
Defines how softkeys, whose labels depend on firmware, are represented.
Defines how text displayed on the instrument's screen is represented.
Lists sales and service office locations in the US and Europe.
Details sales and service contacts for European locations.
Guidance on navigating and performing tests within the Performance Tests chapter.
Covers procedures for verifying instrument functionality during incoming inspections.
Procedure to measure and verify the accuracy of the internal timebase.
Procedure to test the accuracy of the synthesizer's frequency settings.
Procedure to verify the accuracy of the synthesizer's output power.
Procedure to measure and verify the flatness of the RF output power.
Procedure to measure the AM accuracy of the synthesizer.
Procedure to measure the FM accuracy of the synthesizer.
Guidance on performing adjustments and understanding chapter structure.
Procedure to adjust the frequency accuracy of the internal 10 MHz timebase.
Procedure to minimize three specific spurs (125 kHz reference, API1, API2).
Procedures for adjusting sampler assembly components like match and loop gain.
Procedures for adjusting amplifier/multiplier RF output and tracking filters.
Procedures for adjusting the YIG tuned filter and amplifier/filter response.
Procedure to calibrate DAC output voltages for AM/FM modulator.
Procedure to set and calibrate ALC constants for power accuracy.
Procedure to measure and correct power flatness across frequency bands.
Explains what calibration constants are and their role in instrument operation.
Describes the three memory areas reserved for calibration constants.
Procedure to verify the integrity of calibration constants stored in RAM.
Information on setting, disabling, and bypassing the calibration constant password.
Procedure for modifying working data calibration constants.
Procedure to save current calibration constants to a backup file.
Procedure to recall factory default calibration constants.
Details hardware and operating system requirements for automated test software.
Instructions for installing the automated test software from disk.
Guidance on operating the automated test software and configuration limitations.
Overview of automated tests including step attenuator and power flatness.
Procedure to determine the actual attenuation of each attenuator card.
Procedure to measure power flatness and accuracy using a power sensor.
Instructions for configuring power sensors and managing calibration factors.
Map of the ALC menu structure and softkey functions.
Map of the Frequency menu structure and softkey functions.
Map of the Marker menu structure and softkey functions.
Map of the Power menu structure and softkey functions.
Map of the Service menu structure and softkey functions.
Lists the tools necessary for disassembly and reassembly procedures.
Covers disassembly and reassembly of the front panel and its components.
Covers disassembly and reassembly of the rear panel and its components.
Covers disassembly and reassembly of the RF deck assembly.
Covers disassembly and reassembly of the main motherboard.
Lists adjustments and performance tests needed post-repair for each assembly.
Details the process for factory-repaired and tested assembly exchanges.
Provides instructions on how to request replacement parts.
Lists major assemblies with their part numbers and descriptions.
Lists all cables with reference designators, part numbers, and descriptions.
Details hardware components for the front panel assembly.
Details hardware components for the rear panel assembly.
Lists and illustrates the various chassis parts.
Lists accessories, tool kits, and software related to the instrument.
Instructions for cleaning the instrument's internal fan filter.
Instructions for cleaning the instrument's plastic display filter.
Procedure for replacing the instrument's line fuse.
Instructions for safely replacing the CPU battery.
Guidance on cleaning and care of the instrument's output connector.
Information on retrofitting Option 001 to add an attenuator.
Information on retrofitting Option 003 to delete keyboard/display.
Information on retrofitting Option 004 for rear panel RF output.
Information on retrofitting Option 700 for MATE system compatibility.
Information on retrofitting Option 806 for rack mounting.
Guidance on how to interpret instrument history changes and production versions.
