Agilent Technologies 83620A - Page 435

7.
T
o
change
the serial
num
b
er
in
the
\Edit
Sensor"
screen,
scroll
to
the
Serial Num
b
er
selection
[4]
and
press
\Select".
Once
\Select"
has
b
een
pressed,
a
n
um
b
er
m
ust
b
e
entered.
8.
After \Edit
Sensor" is
selected,
\En
ter
T
ext"
should
b
e
displa
y
ed.
En
ter
the
serial
n
um
b
er
and
press
\Return",
then
\Done".
The
mo
del and
new
serial
n
um
b
er should
be
listed in
the table.
9.
Repeat
steps
6
through
8
un
til
all
the
correct
serial
n
um
b
ers
are
displa
y
ed.
10.
No
w
sa
v
e
the
new
serial
n
um
b
ers
in the
Po
wer
Meter
Conguration
le
b
y
scrolling
to
[17]
\Sa
v
e
P
o
w
er
Meter
Conguration" and
pressing
\Select"
then
\Done"
to exit
the
routine.
11.
If
the
cal
factors
need
to
b
e
loaded
for
new
serial
num
bers
or c
hanged for
existing
serial n
um
b
ers,
scroll
to
\Pm
tr
Cal
F
actor"
selection
[3],
and
press
\Select".
A
list
of
serial
n
umb
ers and
sensor
mo
del
n
um
b
ers
should
b
e
displa
y
ed.
12.
Scroll
do
wn
to
the
serial
n
um
b
er
to
b
e
edited
and
press
\Select".
If
the
correct
serial
n
umb
er
is
not
displa
y
ed,
return
to
the
\Pm
tr
Cong"
program
and
rep
eat
en
tering
the
correct
serial
n
um
ber.
When
en
tering
cal
factors
for
a
new
serial
num
ber,
the
message
\F
ailed
attempt
to
access
le
.
.
.
"
will
app
ear.
Press
\Ab
ort".
Read
the
message
display
ed
and
then
press
\OK".
13.
The \Cal
F
actor
Edit
Men
u"
should
no
w
b
e
displa
y
ed.
This
men
u
has
6
options.
Here
is
an
explanation of
each
selection.
[1]
Edit
Cal
F
actors:
Select
\Edit
Cal
F
actors"
to
edit the
cal-factors for
the
serial
n
um
b
er
selected.
After
\Select"
is
pressed
the
cal
factors
are
display
ed. Scroll
to the
line to
be
edited and
press
\Select".
There
are
four
c
hoices
for
editing
the cal
factors.
Value
-Value is used to edit a cal factor. En
ter the new v
alue b
y
typing o
ver the old data. Do not use the delete k
ey.
Frequency - F
requency is used
to edit the frequency
.En
ter the new
value b
yt
yping o
ver the old data. Do not use the delete k
ey.
Insert - Inserts a line in the table at the lo cation
of the poin
ter.
Delete -
Deletes the line in the table at the lo cation of the poin
ter.
HP 8360 Automated Tests 5-25
All manuals and user guides at all-guides.com