Ametek 3050 Series User Manual

Name: Ametek 3050 Series
Brand: Ametek
Rating: 4 (1 reviews)

86 pages

To Next Page

To Previous Page

Installation & Start-Up | 3-7

Figure 3-3a.

Threaded Enclosure

Analyzer Arrangement



NOTE

The unit is intended to be mounted on a horizontal surface or on a verticle surface

with a junction box. Contact Ametek for custom orientations.

Analyzer Serial Number Location3
Table of Contents4
Safety Notes8
Electrical Safety8
Grounding8
Environmental Information (WEEE)9
3050 Slr Moisture Analyzer13
Overview13
Controller Communication14
Veri Ication15
Gas Flow15
Internal Timing15
Calculation of Dewpoint Values for Hydrocarbon Streams16
Specifications19
Operating Environment19
Approvals and Certi Ications19
Ranges20
Outputs20
Data20
Alarms/Alerts20
Lower Detectable Limit20
Sensitivity20
Accuracy20
Reproducibility20
Moisture Generator Value20
Instrument Air Requirements21
Back Pressure Regulator Requirements (if Purchased)21
Sample Inlet Pressure Requirement21
Exhaust Pressure21
Minimum Differential Pressure21
Sample Flow Requirement21
Inlet Gas Temperature21
Power Requirements22
Minimum PC Requirements for Software22
Dimensions22
Net Weight22
Installation and Start up25
Unpacking and Inspection25
Sample System Space Requirements25
Power Requirements25
System Tubing25
Dry Reference Gas25
Sample Gases26
Sample Pressure and Temperature Requirements26
Mechanical Installation28
Electrical Connections29
Analyzer Start-Up35
Interconnect Wiring36
4-20 Ma Output Wiring37
RS232 Wiring38
RS485 Cables39
Status Leds and Alarms41
User Interface43
3050-SLR Moisture con Igurator Software43
Con Igurator Software Installation43
Con Iguring the 305044
General Tab44
PC Communications44
Communication Protocol45
Saving Your Settings45
Live Data46
Con Iguring Multiple Analyzers47
Setup Tab49
Sensor Saver Check Box50
Gas Saver Check Box50
4-20 Ma Output50
Alarm Output50
Set Clock51
Set Dryer Production Code52
Scheduled Zero53
Saving Your Settings53
Flow Adjust56
Test Alarms57
Test Ma Output57
Remote Verification59
Replacement Parts and Maintenance61
Glossary of Terms63
Modbus Communication Interface67
Overview67
Analyzer Modbus Interface Parameters69
Modbus Address69
Communication Parameters69
Modbus Functions70
Exception Code70
Holding Registers71
ID/Status Information78
Example 1: Alarm Enable80
Example 2: Setting the High-Alarm Limit81
Example 3: Setting the Low-Alarm Limit81
Example 4: Enabling "Hold During Verify81
Example 5: Setting the High-End of the Analog Output81
Example 6: Setting the Low-End of the Analog Output82
Example 7: Switching to "Sensor-Saver" Mode82
Example 8: Switch to Dewpoint Readings82
Example 9: Selecting a Sample Gas83
Example 10: Setting Veri Ication Schedule83

Questions and Answers:

Need help?

Do you have a question about the Ametek 3050 Series and is the answer not in the manual?

Ametek 3050 Series Specifications

General

Brand	Ametek
Model	3050 Series
Category	Measuring Instruments
Language	English

Related product manuals

Ametek Land Cyclops 390L

60 pages

Ametek mocon Dansensor ISM-3

Ametek Thermox WDG-VC

164 pages

Ametek SPECTRO ARCOS FHX3X

71 pages

Thermox Series 2000 WDG-IVC

193 pages

Ametek 3050 Series User Manual

Table of Contents

Questions and Answers:

Ametek 3050 Series Specifications

Related product manuals