Analog Devices EVAL-ADuCM355QSPZ - Replaced Figure 9

Analog Devices EVAL-ADuCM355QSPZ

24 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

EVAL-ADuCM355QSPZ Evaluation Board UG-1308

Rev. A | Page 9 of 24

16887-009

Figure 9. IAR Embedded Workbench

Table of Contents

Features1
Equipment Needed1
Documents Needed1
Software Needed1
General Description1
Evaluation Board Photograph1
Changes to Features Section, Equipment Needed Section, Software Needed Section, and General Description Section1
Table of Contents2
Revision History2
Power Configurations4
- Regulator4
Deleted Microusb Connector, P4 Setup Section Heading4
- Changes to Power Configurations Section, Microusb Direct Power Via P4 and ADP7158 LDO Regulator Section, and Figure 2 Caption4
- Section, Jumper Setup with Power Via USB Section, Figure5
- Direct 3.3 V Power Via the AVDD and DVDD Connectors6
- Power Via External 5 V Supply to 2-Pin Connector (P37)6
- Power Via USB from 8-Pin DEBUG Connector (P27)6
Caption, and Power Via External 5 V Supply to 2-Pin Connector (P37) Section6
Connecting an Electrochemical Sensor7
Changes to Connecting an Electrochemical Sensor Section7
Deleted Figure 8; Renumbered Sequentially7
Getting Started with the Tool Chain8
- Downloading the Integrated Development Environment (IDE)8
- Installing the Aducm355 Support Package8
Changed Getting Started with the Tool Chain Section to Getting Started with the Tool Chain Section8
Changes to Downloading the Integrated Development Environment (IDE) Section, Installing the Aducm355 Support Package Section, Running a GPIO Example in IAR Embedded Workbench Section, and Project Folder Structure Section8
- Running a GPIO Example in IAR Embedded Workbench8
- Replaced Figure 99
- Changes to Compiling and Running Firmware Section and Figure 11 Caption10
- Replaced Figure 10 and Figure 1210
- Replaced Figure 1411
- Running a GPIO Example in Keil Μvision11
- Added Running a GPIO Example in Keil Μvision Section, Figure 15, and Figure 16; Renumbered Sequentially11
- Deleted Figure 1911
- Added Figure 17 to Figure 1912
Application Examples13
- Cyclic Voltammetry Example13
- Changes to Application Examples Section, Cyclic Voltammetry Example Section, and Figure 22 Caption13
- Added Figure 2113
- EIS Example14
- Chronoamperometry Example14
- Changes to Figure 23 Caption, EIS Example Section, and Chronoamperometry Example Section14
- Replaced Figure 23 and Figure 2514
- Added Figure 2414
- DC Current Example15
- Replaced Figure 28 and Figure 2915
- Changes to Figure 28 Caption and DC Current Example Section15
- 4-Lead Electrochemical Sensor Example16
Changes to 4-Lead Electrochemical Sensor Example Section16
- Added Figure 3016
- AFE die Watchdog Timer Example17
- Connecting an External Gain Resistor Across the High Speed TIA17
- Moved Connecting an External Gain Resistor Across the High Speed TIA Section, AFE Watchdog Timer Example Section, and Figure 3217
Changes to AFE die Watchdog Timer Example Section17
Aducm355 System Calibration18
- High Speed TIA Gain Resistor Calibration18
Added Aducm355 System Calibration Section18
Moved High Speed TIA Gain Register Calibration Section18
Deleted Figure 2918
Changes to High Speed TIA Gain Resistor Calibration Section18
- Deleted Figure 3318
- Low Power TIA0/TIA1 Gain Resistor Calibration20
Mass Erasing a Device Not Responding to SWD Commands22
Ordering Information23
- Bill of Materials23

Related product manuals

Preview: Analog Devices EVAL-ADE9113

Analog Devices EVAL-ADE9113

Preview: Analog Devices EVAL-AD2428WD1BZ

Analog Devices EVAL-AD2428WD1BZ

Analog Devices EVAL-ADAU1401AEBZ

Preview: EVAL-ADAU1701MINIZ

EVAL-ADAU1701MINIZ

Analog Devices ADAV4601

Preview: Analog Devices AD9361

Analog Devices AD9361

Preview: Analog Devices AD9910

Analog Devices AD9910

Preview: Analog Devices AD9959/PCB

Analog Devices AD9959/PCB

Preview: Analog Devices SSM2167

Analog Devices SSM2167

Preview: Analog Devices 2787A

Analog Devices 2787A

Analog Devices ADAU1701