Arturia CS-80V - Page 82

ARTURIA – CS-80V – USER’S MANUAL
82
volv3
: Volume of track3
volv4
: Volume of track4
volv5
: Volume of track5
volv6
: Volume of track6
volv7
: Volume of track7
volv8
: Volume of track8
9.2 LIST OF ABBREVIATIONS FOR PARAMETERS THAT ARE APPLIED TO A
PARTICULAR TONE.
Each setting begins with « Sx », x being the tone (single) number, from 1 to 8, the
following list is in relation to single 1:
S1AfBr1
: Brilliance of line 1, controlled by the pressure (after touch)
S1AfLe1
: Volume of line 1, controlled by the pressure (after touch)
S1AfBr2
: Brilliance of line 2, controlled by the pressure (after touch)
S1AfLe2
: Volume of line 2, controlled by the pressure (after touch)
S1Detun
: Detuning of line 2 in relation to line 1
S1ev1Al
: Attack level for the envelope of the filters on line 1
S1ev1At
: Attack time for the envelope of the filters on line 1
S1ev1Dc
: Decay time envelope of the filters on line 1
S1ev1In
: Initial level for the envelope of the filters on line 1
S1ev1Re
: Release time for the envelope of the filters on line 1
S1ev2At
: Attack time for the envelope of the VCA on line 1
S1ev2Dc
: Decay time for the envelope of the VCA on line 1
S1ev2Re
: Release time for the envelope of the VCA on line 1
S1ev2Su
: Sustain time for the envelope of the VCA on line 1
S1ev3Al
: Attack level for the envelope of the filters on line 2
S1ev3At
: Attack time for the envelope of the filters on line 2
S1ev3In
: Initial level for the envelope of the filters on line 2
S1ev3Dc
: Decay time for the envelope of the filters on line 2
S1ev3Re
: Release time for the envelope of the filters on line 2
S1ev4At
: Attack time for the envelope of the VCA on line 2
S1ev4Dc
: Decay time for the envelope of the VCA on line 2
S1ev4Re
: Release time for the envelope of the VCA on line 2
S1ev4Su
: Sustain level for the envelope of the VCA on line 2
S1FrHi1
: Line 1 high-pass filter cut-off frequency
S1FrLo1
: Line 1 low-pass filter cut-off frequency
S1FrHi2
: Line 2 high-pass filter cut-off frequency
S1FrLo2
: Line 2 low-pass filter cut-off frequency
S1InBr1
: Brilliance of line 1, controlled by the velocity
S1InLe1
: Volume of line 1, controlled by the velocity
S1InBr2
: Brilliance of line 2, controlled by the velocity
S1InLe2
: Volume of line 2, controlled by the velocity
S1Lev1
: Line 1 VCA level
S1Lev2
: Line 2 VCA level
S1LevF1
: Line 1 filter output level
S1LevF2
: Line 2 filter output level
S1Lf1Sp
: Line 1 LFO speed
S1Lf1Pw
: Line 1 impulse width modulation amplitude
S1Lf2Sp
: Line 2 LFO speed
S1Lf2Pw
: Line 2 impulse width modulation amplitude
S1Mixe
: Mixing of line 1 and line 2
S1M01Am
: Modulation amplitude for line 1 of the matrix
S1M02Am
: Modulation amplitude for line 2 of the matrix