Why is my Autotrol Logix 760 Control Unit not regenerating automatically?
If your Autotrol Control Unit is not regenerating automatically, the AC adapter or motor might not be connected; ensure the power is connected. If the power is connected, the motor might be defective and require replacement.
Why is my Autotrol Control Unit regenerant tank overflowing?
If you're experiencing a regenerant tank overflow with your Autotrol Control Unit, it could be due to several reasons. First, a regenerant valve disc 1 might be held open by foreign matter; manually operate the valve stem to flush away the obstruction. Second, valve disc 2 might not be closed during regenerant draw, causing brine refill; flush out any foreign matter by manually operating the valve stem. Third, there could be an air leak in the regenerant line to the air check; check all connections for leaks. Refer to the instructions. Fourth, an improper drain control for the injector could be the issue; a drain control that is too small with a larger injector will reduce draw rates. Finally, the drain control might be clogged with resin or other debris; clean the drain control.
What to do if Autotrol Logix 760 Control Unit will not draw brine?
If the Autotrol Control Unit is not drawing brine, it could be due to several reasons. First, check for low water pressure and adjust the setting according to the instructions. Next, inspect the drain line for any restrictions and remove them. Also, the injector might be plugged, so clean the injector and screen. If none of these steps work, the injector may be defective and require replacement. Finally, check if valve disc 2 and/or 3 are not closed, remove any foreign matter, and check the disc for closing by pushing in on the stem, replace if needed. Also, the air check valve might be prematurely closed. Put the control momentarily into brine refill, C8. Replace or repair air check if needed.
What does it mean when my Autotrol Logix 760 displays four dashes?
If your Autotrol Control Unit displays four dashes (— — : — —), it indicates a power failure occurred. Press the SET button to reset the time display.
Why does my Autotrol Logix 760 Control Unit regenerate at the wrong time?
If the Autotrol Control Unit regenerates at the wrong time, the controller might be set incorrectly. Correct the time setting according to the instructions.
Why no water flow display on Autotrol 760 Control Unit when water is flowing?
If your Autotrol 760 controller shows no water flow display when water is flowing, first, make sure that the bypass valve is not in the bypass position. If it is, shift it to the not-in-bypass position. Then, check if the meter probe is disconnected or not fully connected to the meter housing and fully insert the probe into the meter housing. Finally, check for any restrictions in the meter turbine rotation due to foreign material in the meter. Remove the meter housing, free up the turbine, and flush with clean water to ensure the turbine spins freely. If not, replace the meter.
How to fix ERR 1 on Autotrol Logix 760?
If your Autotrol Control Unit displays ERR 1, it means the controller power has been connected, and the control is unsure of the operation's state. To resolve this, press the UP arrow to reset the control.
Overview of Logix Series controllers and their functions.
Procedure for initial controller power-up and camshaft positioning.
Detailed steps for configuring system size, time, day, and regeneration settings.
Guidance on setting the correct amount of salt for regeneration.
Instructions for inputting water hardness for 760 Demand controls.
Procedure to reset the controller to its unprogrammed state.
Crucial warning about data loss when resetting the control.
Essential electrical and mechanical safety guidelines for installation.
Detailed explanation of the seven regeneration cycles.
Identification and description of 255 and Performa valve components.
Instructions and diagrams for connecting the water lines and bypass systems.
Procedure to input the system's media volume or select filter mode.
Procedure for setting the desired time for regeneration cycles.
Configuring regeneration frequency for 740 time-clock controls.
Setting calendar override days for 760 demand controls.
Setting the salt amount for regeneration.
Steps to place the conditioner into operation after initial setup.
Details on the camshaft's function and removal/installation.
Table of common problems, causes, and solutions for 700 series controllers.
General| Model | Logix 760 |
|---|---|
| Type | Control Unit |
| Control Type | Electronic |
| Display | LCD |
| Valve Compatibility | Autotrol Valves |
| Programming | User-programmable |
| Backup Battery | Yes |
To Next Page