How to fix letters that are not in the correct case on Avery Dennison MONARCH 9416 XL?
If the letters are not printing correctly on your Avery Dennison Printer, verify that the caps lock is not enabled.
How to troubleshoot Avery Dennison Printer when indicator light is off?
Check the power connections from the power supply to the Avery Dennison Printer and the AC outlet.
What to do if I tried to skip a required field on Avery Dennison MONARCH 9416 XL?
If you're trying to skip a required field on your Avery Dennison Printer, you must enter data into the field before proceeding. Enter the necessary data and then press ENTER to continue.
Why is the keyboard display blank on my Avery Dennison MONARCH 9416 XL Printer?
If the keyboard display is blank on your Avery Dennison Printer, ensure the printer is powered on and the keyboard cable is securely connected. If the keyboard was connected while the printer was on, try turning the printer off and then on again.
How to fix faded or poor quality printing on Avery Dennison MONARCH 9416 XL?
If the Avery Dennison Printer is printing faded or of poor quality, try the following: * Ensure that the supplies and ribbon are loaded correctly. * Clean the printhead. * Check the supplies and ribbon for damage or defects, and reload if necessary. * Ensure ribbon and supply are compatible (for thermal direct supplies, do not load a ribbon). * Adjust the print speed/darkness (contrast).
What to do if Avery Dennison MONARCH 9416 XL stops printing and indicator light turns red?
If your Avery Dennison Printer stops printing and the indicator light turns red, or if the printing is not lined up correctly, try the following: 1. Calibrate the supply by turning off the printer. Load supply for non-peel mode. Press and hold the FEED button while turning on the printer. Release the FEED button after the indicator light starts flashing orange. The printer calibrates the black mark or die cut sensor, measures the label length, prints the test labels, and calibrates the ribbon sensor. To resume normal printing, turn off the printer, wait two seconds, then turn it back on. 2. Try loading a different supply. 3. Make sure the ribbon is not empty. 4. Ensure the black mark/die cut sensor is set correctly for your supply type. 5. Clear any label jams.
Why is my Avery Dennison MONARCH 9416 XL indicator light green but it doesn't print?
If the indicator light on your Avery Dennison Printer is green but the printer isn't printing, try the following: * Check the cable connections from the host to the printer. * Ensure the ribbon and supply are loaded correctly. * Clean the printhead. * Make sure the supply door is closed completely.
What to do if supply exits partially out of Avery Dennison Printer?
If the supply exits partially or skips when using the Avery Dennison Printer, here are a few things to check: * Check for and clear any supply jams within the printer. * Ensure the supplies and ribbon are loaded correctly. * For thermal transfer printing, make sure thermal transfer supply (requires a ribbon) is loaded. For thermal direct printing, make sure thermal direct supply (does not require a ribbon) is loaded.
How to fix Avery Dennison MONARCH 9416 XL when ribbon is not advancing?
To resolve the issue of the ribbon not advancing when printing with your Avery Dennison Printer, calibrate the ribbon sensor.
Why does printing stop and the indicator light turn red on my Avery Dennison MONARCH 9416 XL Printer?
Printing may stop, and the indicator light may turn red, or printing might not line up correctly due to several reasons. You can calibrate the supply by turning off the printer, loading the supply for non-peel mode, pressing and holding the FEED button while turning on the printer, and releasing the FEED button after the indicator light starts flashing ORANGE. The printer will calibrate the black mark or die cut sensor, measure the label length, and print test labels. Then, turn off the printer, wait two seconds, and turn it back on. Alternatively, there may be a problem with the supply, so try loading a different supply. Also, ensure that there are no label jams, and the black mark/die cut sensor is correctly set for your supply type.
General| Print Resolution | 203 dpi |
|---|---|
| Print Speed | 4 ips |
| Connectivity | Serial, Parallel, USB |
| Power Requirements | 100-240 VAC, 50-60 Hz |
| Print Technology | Direct Thermal |
| Maximum Print Width | 4.1 inches |
| Media Type | Labels, Tags |
| Media Width | 1 inch to 4.25 inches |
| Media Thickness | 0.0025 inches to 0.01 inches |
| Operating Temperature | 41°F to 104°F (5°C to 40°C) |
| Humidity | 20% to 85% non-condensing |
To Next Page
