Binder CB-S 170 - Page 5

CB-S / CB-S-UL (E7) 06/2020 page 5/119
23. HOT-AIR STERILIZATION AT 180 °C / 356 °F .................................................... 86
23.1 Overview ........................................................................................................................................... 86
23.2 Performing a hot-air sterilization ....................................................................................................... 87
23.2.1 Preparations for hot-air sterilization ........................................................................................ 87
23.3 Starting and running the hot-air sterilization cycle ............................................................................ 88
23.3.1 Starting sterilization ................................................................................................................. 88
23.3.2 Performance during sterilization ............................................................................................. 89
23.3.3 Completing the entire sterilization cycle ................................................................................. 89
23.4 Prematurely terminating the sterilization cycle – effects ................................................................... 90
23.4.1 Premature termination after less than 6 hours: Ineffective sterilization .................................. 90
23.4.2 Premature termination after more than 6 hours, i.e., during the cooling-down phase:
successful sterilization ............................................................................................................ 91
23.5 Prematurely terminating the sterilization cycle – procedure ............................................................. 91
23.5.1 Cancelling sterilization via the controller menu ...................................................................... 91
23.5.2 Opening the outer door ........................................................................................................... 92
23.5.3 Turning off the chamber .......................................................................................................... 92
24. MAINTENANCE, AND SERVICE, TROUBLESHOOTING, REPAIR, TESTING .. 93
24.1 General information, personnel qualification..................................................................................... 93
24.2 Maintenance intervals, service .......................................................................................................... 94
24.3 Service Reminder .............................................................................................................................. 94
24.4 Gas inlet fine filter ............................................................................................................................. 95
24.5 Simple troubleshooting ...................................................................................................................... 95
24.5.1 General ................................................................................................................................... 95
24.5.2 Temperature ........................................................................................................................... 96
24.5.3 CO
2
......................................................................................................................................... 97
24.5.4 Humidity .................................................................................................................................. 98
24.5.5 Controller ................................................................................................................................ 98
24.5.6 Sterilization ............................................................................................................................. 98
24.6 Sending the chamber back to BINDER GmbH ................................................................................. 99
25. DISPOSAL.......................................................................................................... 100
25.1 Disposal of the transport packing .................................................................................................... 100
25.1.1 Outer chamber packing......................................................................................................... 100
25.1.2 Packing inside the chamber, equipment ............................................................................... 100
25.2 Decommissioning ............................................................................................................................ 101
25.3 Disposal of the chamber in the Federal Republic of Germany ....................................................... 101
25.4 Disposal of the chamber in the member states of the EU except for the Federal Republic of
Germany................................................................
.......................................................................... 102
25.5 Disposal of the chamber in non-member states of the EU ............................................................. 103
26. TECHNICAL DESCRIPTION .............................................................................. 104
26.1 Factory calibration and adjustment ................................................................................................. 104
26.2 Over current protection ................................................................................................................... 104
26.3 Definition of usable volume ............................................................................................................. 104
26.4 CB-S / CB-S-UL technical data ....................................................................................................... 105
26.5 Important conversion data for non-SI units ..................................................................................... 106
26.6 Conversion table for gas inlet pressures, bar – psi ......................................................................... 107
26.7 Equipment and options (extract) ..................................................................................................... 107
26.8 Options, accessories, and spare parts (extract) ............................................................................. 108
26.9 Dimensions...................................................................................................................................... 109
27. CERTIFICATES AND DECLARATIONS OF CONFORMITY ............................. 111
27.1 EU Declaration of Conformity.......................................................................................................... 111
28. PRODUCT REGISTRATION .............................................................................. 113
29. CONTAMINATION CLEARANCE CERTIFICATE ............................................. 114
29.1 For chambers located outside the USA and Canada ..................................................................... 114
29.2 For chambers in the USA and Canada ........................................................................................... 117