What does 'invalid system configuration' mean on my Bosch FW 200 Controller?
If your Bosch Controller displays an invalid system configuration, it means there is an invalid ID in the remote control for the heating circuit. When using FW 200, only IDs 1 to 4 are possible in the remote control.
What to do if Bosch FW 200 says remote control is installed in boiler?
If your Bosch Controller indicates that the remote control is installed in the boiler, mount the remote control in the living area.
What to do if Bosch Controller shows temperature for thermal disinfection not reached in solar tank?
If the Bosch Controller indicates that the temperature for thermal disinfection was not reached in the solar tank, it could be due to the maximum temperature for solar tank being too low. Set a higher maximum temperature for the solar tank. Another reason may be that the delivery rate of the disinfection pump (PE) is too low. Set a higher pump speed on disinfection pump (PE) or, if possible, open flow restrictor more.
How do I fix an invalid remote control configuration on my Bosch Controller?
If your Bosch Controller displays an invalid system configuration related to the remote control, check the system layout and configuration, and modify it if necessary.
What does it mean when my Bosch FW 200 Controller says temperature sensors are reversed?
If your Bosch Controller indicates that the temperature sensors are reversed, it means the temperature sensors (T1 and T2) are reversed. Check the temperature sensors and swap the connections if necessary.
How to fix if heat-up takes too long with Bosch FW 200?
If the heat-up time is too long with your Bosch Controller, the heat-up speed may be set too low. Adjust the heat-up speed to a higher setting, such as “Fast”.
What should I do if the external heating supply temperature sensor is defective on my Bosch FW 200 Controller?
If your Bosch Controller displays that the external heating supply temperature sensor is defective, it means the common temperature sensor (VF) connected to the IPM is defective. Check the common temperature sensor (VF) and replace it if necessary.
How to fix a defective mixer temperature sensor on a Bosch Controller?
If your Bosch Controller indicates a defective mixer temperature sensor, it means the mixer temperature sensor (MF) connected to the IPM is defective. Check the mixer temperature sensor (MF) and replace it if necessary.
What causes a Bosch Controller to be unable to save parameter settings?
If your Bosch Controller is unable to save parameter settings, it may be because a BUS device is configured but not available at present. Check the system structure and configuration, adjust as necessary, and reset parameters on the remote control.
Why is my Bosch Controller unable to save parameter settings?
If your Bosch Controller is unable to save parameter settings, it could be because a BUS device is configured but not currently available. Check the system layout and configuration, modify if necessary, and then set the parameter again.
General| Brand | Bosch |
|---|---|
| Model | FW 200 |
| Category | Controller |
| Language | English |
Details on the functions and operation of the device's controls, including turning dial and buttons.
Explanation of symbols used in the manual and on the device display for various modes and functions.
Details warnings, signal words, and additional symbols used in the manual for clarity and safety.
Crucial safety guidelines for installation, operation, electrical safety, and handling to prevent hazards.
Lists all components included in the product package, shown with a diagram.
Provides detailed technical data for the device, including dimensions, voltage, and protection levels.
Instructions on how to clean the device housing using a damp cloth, avoiding harsh chemicals.
Lists optional accessories like IPM 2, ISM 2, and FB 100 for expanded system control.
Presents a schematic diagram illustrating various system configurations for installation purposes.
Covers the general process of installing the device, including initial steps and safety precautions.
Details the procedure for mounting the device directly within a boiler unit, including cover removal.
Provides instructions and guidelines for securely mounting the device onto a wall.
Explains how to select the optimal location and mount the outdoor temperature sensor for accurate readings.
Briefly mentions mounting other accessories according to code and supplied instructions.
Provides guidance on environmentally responsible disposal of packaging and old components.
Details the process of connecting the device electrically, including BUS connections and routing cables.
Explains how the controls manage room and hot water temperature based on user programs.
Details how to set up weekly programs for heating and domestic hot water for energy savings and comfort.
Guides on navigating the menu system to view and adjust program settings and operating modes.
Explains how to manually select operating modes for heating and domestic hot water.
Covers permanent and temporary adjustments to the desired room temperature settings for heating circuits.
Provides an overview of the menu structure, factory settings, and adjustment ranges for all menu options.
Configuration options for vacation mode, allowing continuous operation mode for several days.
Settings for heating programs, including activation, editing, and viewing program details.
Configuration options for domestic hot water programs, including DHW and recirculation pump settings.
Settings for time, date, display formats, key lock, and language for the control interface.
Parameters for optimizing solar thermal system performance, including tank temperature limits.
Details on setting up weekly heating programs with different operating modes and switch points.
Defines temperature levels for Comfort, Economy, Frost modes and sets heating rate (heat-up speed).
Explains operating modes for DHW with combination boilers and domestic hot water tanks.
Sets timer programs for domestic hot water when using a combi boiler.
Allows user-defined time/temperature profiles for domestic hot water when using a tank.
Specifies when the secondary recirculation pump for domestic hot water should run.
Sets parameters like tank temperature, DHW priority, and recirculation pump cycles.
Details the process and settings for automatic or manual thermal disinfection to prevent bacterial growth.
Instructions for correcting and adjusting the system's time and date settings.
Customizes display formats for time, date, temperature units, and information shown on the display.
Enables or disables the key lock feature to prevent unintended operation of control buttons.
Allows selection of the desired language for the device display.
Sets maximum temperatures for solar tanks (T2, TB, TC) to prevent overheating and manage solar energy.
Optimizes boiler control based on solar yield for DHW and heating circuits, improving efficiency.
Overview of the INFO menu structure, listing display options and their descriptions for various system components.
Provides an overview of the installer settings menu structure, factory defaults, and ranges.
Configures system parameters like DHW setup, heating circuits, and remote controls for proper operation.
Sets heating parameters for each circuit, including type, base line, design temperature, and room influence.
Configures the type of solar system installed, including collector fields and options like thermal disinfection.
Sets specific parameters for solar systems, including pump delta T values and collector temperature limits.
Allows installers to view a log of the last 20 faults, including date, source, and description.
Enables entry of telephone number and name for customer service or technician contact.
Displays system information such as installation date, component details, and software version.
Configures settings for the slab drying function, including temperature, duration, and start date/time.
Allows testing of individual actuators like pumps and mixing valves to verify their functionality.
Sets system-wide heating parameters like minimum outdoor temperature and building storage capacity.
Defines heating circuit types (radiators, floor heating) and associated parameters for optimal performance.
Selects the installed solar basic system and configures options like collector fields and heat exchangers.
Steps for commissioning the solar thermal system, including filling, bleeding, and parameter checks.
Resets all solar system parameters and installer settings to factory defaults, requiring re-commissioning.
Sets parameters for the standard solar system, particularly for domestic hot water provision.
Configures parameters for using solar energy to boost heating, including return temperature raising.
Sets parameters for a second collector field (Option A), including pump delta T and operating modes.
Configures parameters for the solar recharge system, including pump delta T and DHW reload pump modes.
Selects the configuration for the high/low priority system type, defining tank charging priorities.
Sets parameters for an external heat exchanger used with the solar system, focusing on the secondary circuit pump.
Configures thermal disinfection for solar tanks (E option), including pump modes and tank selection.
Sets parameters for automatic solar optimization, requiring collector area, type, and climate zone.
Explains how to interpret fault displays, identify fault numbers, BUS devices, and fault descriptions.
Provides solutions for common operational problems that do not involve display error codes.
Provides default and ready-made heating programs for copying and customization for heating circuits.
Details how to set the DHW program, summarizing factory settings and providing space for personal settings.
Explains how to set the hot water circulation program, summarizing factory and personal settings.
To Next Page
