9
Product Description
PS602P Rear Panel
1. INPUT 1 & 2 - Balanced XLR/TRS and unbalanced RCA line-level input connectors. Use either
balanced or unbalanced input type, but not both simultaneously per input channel.
2. USB - This allows you to use the PC-based PowerShare
TM
Editor Software to configure the advanced
features of the amplifier. The CONFIG DIP switch must be set to SOFTWARE to configure the amplifer
using the PowerShare Editor Software.
3. CHANNEL 1 & 2 EQ - Each dial provides loudspeaker equalization presets per channel: DS 16, DS
40, DS 100, FS3B, 402, 802, MA12EX, RMU105, and RMU108. Use the Flat setting for FS3 Systems, or
for loudspeakers that are not Bose or that do not require EQ. When EQ is selected, the Vpeak and
Vrms limiters for that loudspeaker are automatically loaded. Use the PowerShare Editor Software to
adjust any of these parameters. In Hi-Z output mode, a 50 Hz high pass filter (HPF) is automatically
added to the Hi-Z selected outputs. The loudspeaker EQ is applied after the 50 Hz HPF.
4. MUTE - Contact closure connection where a short across the mute connector will mute all outputs.
This is the Normally Open (NO) default state. The mute polarity can be inverted to Normally Closed
(NC), where an open across the mute connector will mute all outputs, using the PowerShare Editor
Software.
5. DIP Switches - A bank of switches used to set the amplifier configuration. All switches set to the left
position is the standard configuration.
• AUTO STANDBY - If enabled (ON), the amplifier goes into standby mode after twenty minutes
without an input signal. If in standby mode and an audio signal is detected, the amplifier will
automatically wake and amplify audio within 1 second. The OFF position disables this feature.
• GLOBAL OUT - Sets the output capability to 70 Vrms or 100 Vrms, for all outputs that have their
OUTPUT DIP switch set to HI Z. In 70 Vrms mode, a 100 Vpeak limiter is automatically loaded. In
100 Vrms mode, a 141 Vpeak limiter is automatically loaded.
• CONFIG - In REAR mode, only the rear panel EQ settings are required to configure the amplifier. In
SOFTWARE mode, the PowerShare Editor Software configures the amplifier, and the rear panel EQ
switches are ignored. The rest of the DIP switch settings are always independent of the
PowerShare Editor Software settings.
• SENSITIVITY - Select 4 dBu or 12 dBu as the amplifier sensitivity for the XLR/TRS line-level inputs.
The unbalanced RCA input sensitivity is -10 dBV in the 4 dBu sensitivity setting, and -2 dBV in the 12
dBu sensitivity setting.
• OUTPUT 1 - Select 70/100 V high impedence output (HI Z) or 4-8 ohm low impedence output
(LOW Z) for OUTPUT 1.
• OUTPUT 2 - Select 70/100 V high impedence output (HI Z) or 4-8 ohm low impedence output
(LOW Z) for OUTPUT 2.
6. OUTPUT - NL4 and binding post outputs for each output. NL4 OUTPUT 1 combines both outputs,
while NL4 OUTPUT 2 is only for OUTPUT 2. This gives access to both outputs on one NL4 four-con-
ductor cable from NL4 OUTPUT 1, or two NL2 two-conductor cables can be connected to each output
instead. Each channel can deliver up to 600 Watts regardless of load into 4 ohms, 8 ohms, 70 V RMS,
or 100 V RMS. Outputs are not bridgeable.
7. AC Inlet – Removing the AC cord when the amplifier is on is equivalent to powering down using the
front panel power switch, and is an acceptable power-down method.
1
2
1. FLAT
2. DS16
3. DS40
4. DS100
5. FS3B
6. 402
7. 802
8. MA12EX
9. RMU105
0. RMU108
100-240V ~ 50/60Hz 700W MAX
PowerShare
PS602P
MUTE
AUTO STANDBY
SENSITIVITY
GLOBAL OUT
OUTPUT 2
OUTPUT 1
CONFIG
ON
Low Z
SOFTWARE
12 dBu
100V
Low Z
OFF
Hi Z
REAR
4 dBu
70V
Hi Z
4
6
9
0
7
8
3
2
1
5
4
6
9
0
7
8
3
2
1
5
12345 6 7
To Next Page
Loading...
Need help?
General