Why does my Brother Printer show a 'Connection Error'?
A 'Connection Error' on your Brother printer indicates that other devices are attempting to connect to the Wi-Fi Direct network simultaneously. To resolve this, ensure no other devices are trying to connect to the Wi-Fi Direct network, and then attempt to configure the Wi-Fi Direct settings again.
What to do if my Brother Printer shows a 'No Device' error?
If your Brother printer displays a 'No Device' error, it means the printer can't find your mobile device. Here’s what to do: * Ensure both your printer and mobile device are in Wi-Fi Direct mode. * Move the mobile device closer to the Brother printer. * Remove any obstructions between the devices. * If manually configuring Wi-Fi Direct, verify the password is correct. * If your mobile device requires IP address configuration, ensure it's set to DHCP.
How to fix Brother Printer when wireless network setup configuration cannot be completed?
If you cannot complete the wireless network setup configuration on your Brother Printer, here are a few things to try: First, turn your wireless router off and then back on, and try configuring the wireless settings again. Second, double-check and make sure you're choosing the correct security settings. You might find these settings on your WLAN access point/router or by contacting your Internet provider or network administrator. Third, confirm that the MAC address of your Brother machine is allowed in the filter; you can usually find this on the printer's control panel. Also, make sure you're typing the correct SSID name or Network Key manually. Lastly, try using the Network Connection Repair Tool.
What to do if my Brother Printer says 'Connection Fail'?
If you see a 'Connection Fail' message on your Brother printer, it means the printer and your mobile device aren't communicating properly during setup. To fix this: * Move your mobile device closer to the Brother printer. * Ensure there are no obstructions between the printer and the mobile device. * If using the PIN Method of WPS, verify that you've entered the correct PIN code.
What to do if my Brother MFC-8510DW says 'Out of Memory'?
If your Brother All in One Printer displays 'Out of Memory', the machine’s memory is full. You can press Start to send or copy the scanned pages. Alternatively, press Stop/Exit and wait until the other operations in progress finish, and then try again. Clear the faxes from the memory by printing them to restore the memory to 100%, then turn off Fax Storage.
Why is the function 'Not Available' on my Brother MFC-8510DW?
If your Brother All in One Printer displays 'Not Available', the requested function is not permitted to all User IDs by Secure Function Lock 2.0. Contact your administrator to check your Secure Function Lock Settings.
Why does my Brother All in One Printer say 'Access Denied'?
If your Brother All in One Printer shows 'Access Denied', the function you want to use is restricted by Secure Function Lock 2.0. Contact your administrator to check your Secure Function Lock Settings.
How to fix 'No Toner' error on Brother All in One Printer?
If your Brother All in One Printer displays 'No Toner', the toner cartridge or the drum unit and toner cartridge assembly is not installed correctly. Remove the drum unit and toner cartridge assembly, remove the toner cartridge from the drum unit, and re-install the toner cartridge back into the drum unit again. Re-install the drum unit and toner cartridge assembly back in the machine. If the problem continues, replace the toner cartridge.
Why does my Brother MFC-8510DW say 'Manual Feed'?
If your Brother All in One Printer displays 'Manual Feed', manual was selected as the paper source when there was no paper in the MP tray. Place paper in the MP tray. If the machine is in Pause mode, press Start.
How to resolve 'Size mismatch' error on Brother MFC-8510DW?
If your Brother All in One Printer displays 'Size mismatch', the paper in the tray is not the correct size. Load the correct size of paper in the tray and set the 'Paper Size' (Menu, 1, 2, 2).
General| Print Technology | Laser |
|---|---|
| Functionality | Print, Copy, Scan, Fax |
| Print Resolution | 1200 x 1200 dpi |
| Connectivity | USB, Ethernet, Wi-Fi |
| Automatic Duplex Printing | Yes |
| Paper Capacity | 250 sheets |
| Automatic Document Feeder (ADF) | Yes |
| ADF Capacity | 50 sheets |
| Scanning Resolution | 1200 x 1200 dpi |
| Fax Speed | 33.6 Kbps |
| Operating Systems | Windows, macOS, Linux |
| Mobile Printing | Brother iPrint&Scan, Google Cloud Print, AirPrint |
| Maximum Paper Size | Legal |
| Scan Type | Flatbed |
To Next Page