What to do if my Brother MFC-8510DW says 'Wrong Paper Size'?
If your Brother All in One Printer displays 'Wrong Paper Size', the machine cannot find paper of the same size in any other tray after the tray currently in use has run out of paper during a copy operation. Load the paper in the paper tray shown on the LCD.
How to fix 'Fuser Error' on Brother All in One Printer?
If your Brother All in One Printer displays 'Fuser Error', the temperature of the fuser unit does not rise to a specified temperature within the specified time. Turn the power switch off, wait a few seconds, and then turn it on again. Leave the machine idle for 15 minutes with the power on.
Why does my Brother MFC-8510DW say 'Cooling Down Wait for a while'?
If your Brother All in One Printer displays 'Cooling Down Wait for a while', the temperature of the drum unit or toner cartridge is too hot. Make sure that you can hear the fan in the machine spinning and that the exhaust outlet is not blocked by something. If the fan is spinning, remove any obstacles that surround the exhaust outlet, and then leave the machine turned on but do not use it for several minutes. If the fan is not spinning, disconnect the machine from the power for several minutes, then reconnect it.
What to do if my Brother Printer cannot complete the Wi-Fi Direct network setup configuration?
First, double-check the SSID and password. If your Brother machine is a G/O (Group Owner) in manual configuration, the SSID and password are on the machine's control panel. If your mobile device is a G/O, the SSID and password appear on the mobile device's screen. If the issue persists, ensure your Brother machine is within 3.3 feet (1 meter) of the mobile device without obstructions like walls or furniture. Also, move wireless computers, Bluetooth devices, microwaves, and cordless phones away from the Brother machine and mobile device.
What does 'Drum Stop' mean on my Brother All in One Printer?
If your Brother All in One Printer displays 'Drum Stop', it is time to replace the drum unit. Replace the drum unit.
How to fix 'Cartridge Error Put the Toner Cartridge back in' on Brother All in One Printer?
If your Brother All in One Printer displays 'Cartridge Error Put the Toner Cartridge back in.', it means the toner cartridge is not installed correctly. Pull out the drum unit and toner cartridge assembly, remove the toner cartridge, and put it back into the drum unit again. Then, put the drum unit and toner cartridge assembly back into the machine.
What to do if my Brother MFC-8510DW All in One Printer says 'Cover is Open'?
If your Brother All in One Printer shows 'Cover is Open', it means the front cover, ADF cover, or fuser cover is not completely closed, or paper was jammed in the back when you turned on the power. Ensure the front cover and ADF cover of the machine are closed. If the ADF is open while loading, close it and press Stop/Exit. Also, close the fuser cover, and if paper was jammed behind it, remove the paper, then close the cover and press Start.
How to fix 'No Paper' error on Brother MFC-8510DW All in One Printer?
If your Brother All in One Printer displays 'No Paper', it means the machine is out of paper in the specified tray or all trays, or paper is not correctly loaded. Refill paper in the paper tray shown on the LCD, ensuring the paper guides are set to the correct size. Alternatively, remove the paper and load it again, making sure the paper guides are correctly adjusted.
Where to find Brother Software machine's network settings, such as IP address?
To find your Brother machine's network settings, such as the IP address, print the Network Configuration Report. See Printing the Printer Settings Page (For HL-5450DN(T)) uu page 29 or Printing the Network Configuration Report (For other models) uu page 29.
How to fix Brother Software when I cannot communicate with my Brother machine using SSL?
To communicate with your Brother machine using SSL, ensure you obtain a valid certificate and install it on both your machine and computer. Also, verify that the port setting of your machine is correct. You can confirm your machine’s port setting on the Web Based Management screen by clicking Network, Protocol, and then HTTP Server Settings.
General| Print Technology | Laser |
|---|---|
| Functionality | Print, Copy, Scan, Fax |
| Print Resolution | 1200 x 1200 dpi |
| Connectivity | USB, Ethernet, Wi-Fi |
| Automatic Duplex Printing | Yes |
| Paper Capacity | 250 sheets |
| Automatic Document Feeder (ADF) | Yes |
| ADF Capacity | 50 sheets |
| Scanning Resolution | 1200 x 1200 dpi |
| Fax Speed | 33.6 Kbps |
| Operating Systems | Windows, macOS, Linux |
| Mobile Printing | Brother iPrint&Scan, Google Cloud Print, AirPrint |
| Maximum Paper Size | Legal |
| Scan Type | Flatbed |
To Next Page