CalAmp Viper 100 User Manual

APPENDIX A – SPECIFICATIONS
These specifications are typical and subject to change without notice.
GENERAL
Model Numbers
Frequency Range
Channel Bandwidths Available
Model Numbers, Frequency
Range and Bandwidth
140-5018-502
140-5018-600
140-5028-502
140-5028-504
140-5048-302
140-5048-400
140-5048-502
140-5048-600
140-5098-304
140-5098-502
140-5098-504
136 – 174 MHz
136 – 174 MHz
215 – 240 MHz
215 – 240 MHz
406.125 – 470.000 MHz,
406.125 – 470.000 MHz,
450.000 - 511.975 MHz
450.000 - 511.975 MHz
880 – 902 MHz
928 – 960 MHz
928 – 960 MHz
6.25 kHz, 12.5 kHz, 25 kHz, 50 kHz
6.25 kHz, 12.5 kHz, 25 kHz, 50 kHz
6.25 kHz, 12.5 kHz, 25 kHz, 50 kHz
6.25 kHz, 12.5 kHz, 25 kHz, 50 kHz,
100kHz
6.25 kHz, 12.5 kHz, 25 kHz, 50 kHz
12.5kHz, 25kHz (ETSI, AS/NZ)
6.25 kHz, 12.5 kHz, 25 kHz, 50 kHz
12.5kHz, 25kHz (ETSI, AS/NZ)
12.5 kHz, 25 kHz, 50 kHz, 100 kHz
12.5 kHz, 25 kHz, 50 kHz
12.5 kHz, 25 kHz, 50 kHz, 100 kHz
Frequency Stability
1.0 ppm
Modes of Operation
Simplex, Half-Duplex
Frequency Increment
1.25 kHz
Power Source
VDC, Negative GND
The Viper is UL approved when powered with a listed Class 2 power supply.
RF Impedance
50 Ω
Operating Temperature
-30° to + 60° C
Storage Temperature
-40° to + 85° C, 95% non-condensing RH
Operating Humidity
5% to 95% non-condensing RH
Rx Current Drain at 25°C
DC Input 10V
DC Input 20V
DC Input 30V
520 mA (max)
450 mA (typ)
270 mA (max)
240 mA (typ)
190 mA (max)
170 mA (typ)
Tx Current Drain at 25°C
Power Out
DC Input 10V
DC Input 20V
DC Input 30V
Max Pwr
5.8 A (max)
3.6 A (typ)
2.5 A (max)
1.8 A (typ)
1.6 A (max)
1.2 A (typ)
30 dBm (1W)
1.6 A (max)
1.2 A (typ)
0.8 A (max)
0.6 A (typ)
0.6 A (max)
0.4 A (typ)
Cold start
35 seconds
Nominal Dimensions
5.50" W x 2.125” H x 4.25" D (13.97 x 5.40 x 10.8 cm)
Shipping Weight
2.4 lbs. (1.1 Kg)
Mounting Options
Mounting plate/pattern & DIN Rail
Fan Output
5VDC, 400mA max.

CalAmp Viper 100 Specifications

General

Brand	CalAmp
Model	Viper 100
Category	Network Router
Language	English