Cardinal 220 - Serial Port Configuration

20
SERIAL? - Serial Input/Output
If serial input/output setup is desired, press the
1/YES
key, then the
ENTER
key. Otherwise
press the ENTER key to advance to
TABS?
.
BAUD 1
(Allowable values are: 12, 19, 24, 38, 48, 96 or 115)
12 = 1200 Baud 24 = 2400 Baud 48 = 4800 Baud 96 = 9600 Baud
19 = 19.2k Baud 38 = 38.4k Baud 115 = 115.2k Baud
.
PARITY 1
(Allowable values are: 0 = No Parity, 1 = Odd Parity, or 2 = Even Parity).
BITS 1
(Allowable values are: 7 or 8).
STOPS 1
(Allowable values are: 1 or 2).
•
If
USA=YES
or
MODE OF OP=1
, advance to
CONT 1=
ETR able
(YES = Enabled, NO = Disabled)
CONT 1
(YES = Continuous Output, NO = No Continuous Output)
If ETR able=YES and CONT 1=YES , advance to BAUD 2=
If ETR able=NO and CONT 1=YES.
TYPE (Allowable values are: 0 = SMA, 1 = SB-400,
2 = SB-200 or 3 = Rice Lake IQ355).
BAUD 2
(Allowable values are:
12
,
19
,
24
,
38
,
48
,
96
or
115
)
12 = 1200 Baud 24 = 2400 Baud 48 = 4800 Baud 96 = 9600 Baud
19 = 19.2k Baud 38 = 38.4k Baud 115 = 115.2k Baud
.
PARITY 2
(Allowable values are: 0 = No Parity, 1 = Odd Parity, or 2 = Even Parity).
BITS 2
(Allowable values are: 7 or 8).
STOPS 2
(Allowable values are: 1 or 2).
CONT 2
(YES = Continuous Output, NO = No Continuous Output)
If
CONT 2=NO
, advance to
TABS?
.
If
CONT 2=YES
.
TYPE
(Allowable values are:
0
= SMA,
1
= SB-400,
2 = SB-200 or 3 = Rice Lake IQ355).
TABS? - Print Tab Settings
To configure the Print Tab Settings, press the
1/YES
key, then the
ENTER
key. Otherwise
press the ENTER key to advance to
FINE SPAN?
.
The general format for the input is A = YY.XX where A is the character identifying the data
printed, YY is the number of lines down and XX is the number of spaces to the right.
NOTE!
Enter 00 in either location, YY or XX, to disable the data from printing.
PORT= (Allowable values are: 1 or 2).
NOTE! Although either port can be used for the printer port, it is recommended to
use the bi-directional port 1 with a bi-directional cable.
PRT BEG
(Print beginning string)
If
MODE OF OP = 0
,
2
,
3
, or
4
, advance to
ID=
.
If
MODE OF OP=1
(ID Storage)
TMP ID1=
(The First temporary ID prompt print position)
TMP ID2=
(The Second temporary ID prompt print position)
TMP ID3=
(The Third temporary ID prompt print position)
TP TIME=
(The temporary ID Time print position)
TP DATE=
(The temporary ID Date print position)
STO WT=
(The ID Stored Weight print position)