Carrier 23XRV - Page 78

To Next Page

To Previous Page

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.

Catalog No. 04-53230010-01 Printed in U.S.A. Form 23XRV-5SI Pg 78 1016 10-14 Replaces: 23XRV-4SI

Main Page

Safety Considerations1
- Installation Instructions1
- Table of Contents2
General2
Introduction2
Job Data3
Installation3
- Inspect Shipment3
- Identify Machine3
Step 1 - Receive the Machine3
- Installation Requirements4
- Provide Machine Protection4
Step 2 - Rig the Machine10
- Control Center Components11
- Machine Electrical Data Nameplate12
- Drive Assembly and Power Module Ratings13
- Machine Rigging Guide14
- 23XRV Heat Exchanger Sizes A,B Dimensions16
- 23XRV Heat Exchanger Sizes 30-57 Dimensions17
- 23XRV Compressor and Motor Weights18
- 23XRV Maximum Component Weights18
- 23XRV Waterbox Nozzle Sizes18
- VFD (Variable Frequency Drive) Weight Table18
- 23XRV Cooler Frame Size A1-A6, B1-B6 Heat Exchanger Weights19
- 23XRV Additional Data for Cooler Marine Waterboxes20
- 23XRV Code 30-57 Heat Exchanger Weights20
- 23XRV Additional Data for Condenser Marine Waterboxes21
- 23XRV Waterbox Cover Weights, Frames 3,4,521
- 23XRV Waterbox Cover Weights, Frames A/B22
- Rig Machine Components22
  - Electrical Cable Routing (Unit with R Compressor)23
  - Electrical Cable Routing (Unit with P Compressor)24
- Separate Cooler and Condenser24
Step 3 - Separate Machine Components24
- Cooler/Discharge Pipe Assembly Removal (Unit with R Compressor)25
- Cooler/Discharge Pipe Assembly Removal (Unit with P Compressor)26
- Chiller End View27
- Evaporator Refrigerant Liquid Temperature Sensor on Bottom of Cooler27
- Remove the Controls/Drive Enclosure27
- Separate the Compressor29
- Separate the Vaporizer from the Condenser34
- Oil Concentrator Removal, Q and R Compressors (Unit with R Compressor)34
Install VFD34
- Oil Concentrator Removal, P Compressor35
- Oil Reclaim Piping (Unit with R Compressor Shown)35
- Oil Reclaim Components (Unit with R Compressor)36
- Motor Terminal Box (Q and R Compressors)36
- Motor Terminal Insulation (Q and R Compressors)37
- Motor Terminal Box (P Compressor)37
- Install Standard Isolation38
- Motor Terminal Insulation (P Compressor)38
Install Machine Supports38
- Motor Ground Cable39
- VFD Refrigerant Connectors39
- 23XRV Frame Size a Machine Footprint40
- 23XRV30-57 Machine Footprint40
- 23XRV Frame Size B Machine Footprint41
- Install Accessory Isolation41
  - Standard Isolation41
  - 23XRV Accessory Spring Isolation42
- Install Spring Isolation42
- Install Water Piping to Heat Exchanger42
Step 6 - Connect Piping42
- Piping Flow Data43
- Optional Pumpout Unit and Storage Tank47
- Optional Pumpout System Piping Schematic with Storage Tank48
- Install Vent Piping to Relief Valves49
- Grounding the Controls/Drive Enclosure51
- Installing Input Power Wiring51
- Relief Valve Locations51
Step 7 - Make Electrical Connections51
- Typical Field Wiring Schematic (LF-2 VFD)53
- Enclosure56
- Notes to Fig.6056
- Pic III Control Component Layout57
- Connect Control Inputs/Outputs59
- Connect Starter59
- Wiring the Field Wiring Terminal Strips for STD Tier VFD59
Completing the Installation68
Checking the Installation68
Oil Pump and Oil Heater68
Connect Control Wiring68
- Interface68
Carrier Comfort Network68
Cable Manufacturers69
Bacnet Communication Option Wiring69
Lead-Lag Control Wiring69
Install Field Insulation69
- UPC Open Controller70
- Network Wiring70
- BT485 Terminator Installation71
- MS/TP Wiring Recommendations71
- Open System Wiring Specifications and Recommended Vendors72
- Lead/Lag Control Wiring, Parallel Flow Application73
- Series Flow Application74
- 23XRV Installation Area (P Compressor)75
- 23XRV Installation Area (Q Compressor)76
- 23XRV Installation Area (R Compressor)77
- Installation Start-Up Request Checklist79

Carrier 23XRV - Page 78

Table of Contents

Related product manuals