Casio XJ-UT312WN User Manual

44
Auto Projection Off is disabled (Off) under initial projector default settings. To enable Auto Projection
Off, change “Screen Settings 3 Auto Projection Off” (page 58) on the Setup Menu to “Enable”.
Projection Light Off Conditions
If the image input signal from the input source device to the projector is lost for some reason while
projection is being performed, the no signal screen (page 58) or the network standby screen* appears
first. If no operation is performed for about 10 seconds, the projection light turns off and audio
becomes muted.
The following message will be displayed for about five seconds before the light turns off: “Auto
Projection Off is enabled. The projector will stop projecting.”
Auto Projection Off operation is not affected by whether audio is being input.
* The network standby screen appears when the source setting is “Network”. It indicates that the
projector is standing by for a network connection (wired LAN or wireless LAN). For details about
projection using a network connection, refer to the separate “Network Function Guide”.
Auto Projection Off is not triggered while any one of the following conditions exists.
 If there has been no projection from any input source since the projector was turned on.
 While a template (page 49), the countdown timer (page 52), or a test pattern (page 51) is being
projected.
 While an auto input search operation is in progress (page 39).
Projection Light Restoration Conditions
The projection light will turn back on when the currently selected input source resumes signal input
(or, in the case of the “Network” input source, a network connection starts projection), or when a key
operation is performed on the projector or its remote controller.
Auto Power Off Following Projection Light Off
If the “Auto Projection Off” setting is “Enable”, the Auto Power Off trigger time is fixed at 20 minutes
after the projection light is turned off. This is true regardless of the current Auto Power Off setting
(page 60).
Projector Operation While the Projection Light is Off
 The POWER/STANDBY indicator (green) flashes slowly while the projection light is turned off by the
Projection Light Off function.
 Auto Power Off will be triggered if no projector key operation is performed for approximately 20
minutes after the projection light turns off.
Enabling and Disabling Auto Projection Off
Auto Projection Off Projection Light Control

Casio XJ-UT312WN Specifications

General

Number of colors	1.073 billion colors
Native aspect ratio	16:10
Projection distance	0.06 - 0.4 m
Vertical scan range	50 - 85 Hz
Horizontal scan range	15 - 91 kHz
Projection technology	DLP
Contrast ratio (typical)	20000:1
Screen size compatibility	50 - 110 \
Projector native resolution	WXGA (1280x800)
Keystone correction, vertical	-5 - 5 °
Noise level	37 dB
Password protection	Yes
Light source type	Laser/LED hybrid
Service life of light source	20000 h
Focus	Manual
Offset	70 %
Fixed focal length	4.2 mm
Aperture range (F-F)	2.3 - 2.3
Full HD	-
Supported video modes	480i, 480p, 576i, 576p, 720i, 720p, 1080i, 1080p
Analog signal format system	NTSC, PAL, PAL 60, PAL M, PAL N, SECAM
Supported graphics resolutions	1920 x 1200 (WUXGA)
HDMI connector type	Full-size
Serial interface type	RJ-45, RS-232C
USB 2.0 ports quantity	2
S-Video inputs quantity	0
Wi-Fi standards	802.11b, 802.11g, Wi-Fi 4 (802.11n)
Cables included	AC
Operating temperature (T-T)	5 - 35 °C
Operating relative humidity (H-H)	20 - 80 %
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.23 W
Power consumption (typical)	170 W
Built-in display	No
Placement	Ceiling
Product type	Ultra short throw projector
Product color	White
Market positioning	Short throw
Cable lock slot type	Kensington
RMS rated power	16 W

Weight and Dimensions

Depth	333 mm
Width	338 mm
Height	141 mm
Weight	5900 g