Cessna T182 Series User Manual

MODEL 182 & T182 SERIES SERVICE MANUAL
3-1. FUSELAGE.
3-7. WINDOWS.
3-2.
WINDSHIELD
AND
WINDOWS.
3-8.
MOVABLE.
(See figure
3-3.)
3-3. DESCRIPTION.
The windshield and windows 3-9.
DESCRIPTION. A movable window, hinged
at
are single-piece, acrylic panels, set in sealing
strips the top, is installed in the left
cabin door, and may
strips and held by formed retaining strips, secured to also be installed in the right cabin door, as optional
fuselage with
screws and rivets. H.B Fuller FS-4291 equipment.
A rubber seal is cemented to the inside
sealant is applied to all
edges of the windshield
and of the window
frame, using 3M Co.
EC-800 adhesive,
windows,
with exception
of
wing root
area. The
or equivalent.
wing root
fairing has a heavy
felt strip that com-
pletes the windshield
sealing.
3-10. REMOVAL
AND
INSTALLATION.
a. Disconnect
window stop
(3).
3-4.
WINDSHIELD.
(See
figure
3-2.)
b.
Remove
pins
from
window
hinges.
c. To remove
frame from plastic panel,
drill out
3-5.
REMOVAL.
blind
rivets
at
frame
splice.
a. Remove
magnetic
compass.
(See
Section
16.)
d.
Reverse
preceding
steps
for
installation.
b. Remove wing
that sealing strip and
an adequate coating of
Presstite
If windshield is to be reinstalled,
be sure to
protect
windshield
during removal.
d. With two people
sitting in the airplane placing
3-12. DESCRIPTION.
The rear
window is a one-
their feet
against the
windshield,
just above
the cen-
piece
acrylic plastic
panel,
set in sealing
strips,
terline,
press upward
on windshield forcing
it out of and
held inplace by retaining
strips.
lower retainers.
e. Clean sealer from
inner sidewalls and
bottom of 3-13.
REMOVAL AND
INSTALLATION.
retainers.
a. Remove upholstery
as necessary to expose
retainer
strips
inside cabin.
3-6. INSTALLATION.
b. Drill
out rivets as necessary
to remove re-
a. If new windshield is to be installed. remove pro- tainers on both sides and lower edge of window.
tective cover and clean, take care
not to scratch c. Remove window
by starting at aft edge, and
windshield.
pulling window into cabin area.
b. Apply new felt
to edges of windshield.
d.
Reverse preceding steps
for installation.
c. Apply a strip
of sealer (H.B. Fuller FS-4291)
e. When installing a new rear window, check
fit
along the sides and bottom of
felt. and exercise
care not to crack panel.
d. Position
bottom edge of windshield
into lower
f. File or
grind away excess plastic.
retainer.
g. Install
sealing strips, and apply
an adequate
e.
Using
a piece of
bent sheet
metal
(8 in. wide
x
coating
of sealing
compound,
to prevent
leaks.
length of top edge
of windshield) placed
under top
edge
of upper retainer.
bow
windshield
and guide
top
3-14.
OVERHEAD.
(See figure
3-2.)
edge of windshield
into upper retainer using
bent
sheet
metal in a
shoe horn
effect.
3-15.
DESCRIPTION.
Overhead cabin
windows,
f. Install air
vent tubes.
located in the cabin
top, may be
installed. These
g. Install wing
fairings.
windows
are one-piece acrylic
plastic panels, set
h. Install magnetic
compass.
(See Section
16.)
in sealing strips,
and held in
place by retaining
strips.
3-16. REMOVAL AND INSTALLATION.
a. Remove headliner and trim panels.
b. Drill out rivets as necessary to remove retainer
strips, remove window.
3-2
Revision
1

Cessna T182 Series Specifications

General

Engine Type	Lycoming IO-540-AB1A5
Horsepower	230 hp
Seating Capacity	4
Service Ceiling	18, 100 feet
Takeoff Distance	1, 600 feet
Landing Distance	1, 350 ft
Type	Single-engine
Max Takeoff Weight	3, 100 lb
Wingspan	36 ft
Length	29 ft
Height	9 feet 3 inches
Fuel Capacity	92 US gal (348 L)