Cessna T182 Series User Manual

MODEL 182 &
T182 SERIES SERVICE
MANUAL
1/2
" (TYP)
1-11/16 "R
1-7/8 "R (TYP)
·- L
2. 135 -"
MATL:
4130 (Rc.
35-38)
Figure 11-4. Oil Filter
Adapter Wrench Fabrication
11-47. FULL-FLOW
OIL FILTER.
SERIAL 182-
67042
& ON; F18200130
THRU F18200169.
h. Start
engine and check
for proper
oil pressure.
Check
for oil
leakage after
warming up
the engine.
11-48. DESCRIPTION. An external oil filter may be m. Again check for oil leakage after engine has been
installed
on the engine.
The filter and
filter adapter
run at high
power setting (preferably
a flight
around
replace the regular engine
oil pressure screen.
The the field).
filter is a throw-away
type spin-on
filter which has an
i. Check to make sure
filter can has not been
mak-
internal bypass valve.
ing contact
with any adjacent
parts due to engine
torque.
11-49. REMOVAL
AND INSTALLATION.
(See figure j.
While engine is still warm,
recheck filter (6),
to
11-5.)
assure proper tightness.
a. Remove engine cowling in accordance with para-
graph 11-3.
11-50.
FILTER ADAPTER.
b. Remove safety wire (7) from filter, (6).
c.
Unscrew filter from
adapter, (3).
11-51.
REMOVAL. (See
figure 11-5.)
a.
Remove filter assembly
in accordance with
para-
NOTE
graph 11-49.
NOTE
Teledyne Continental Motors recommends
that the spin-on filter
be inspected. Refer
A special
wrench adapter
for adapter nut (2)
to Continental Aircraft Engine
Service Bulle- (Part No. SE-709)
is available from the
tin M74-2, dated 16 January
1974. Cessna
Supply Division. or one may be
fabricated as shown in figure 11-4. Remove
d. Before installing
oil filter (6) lightly lubricate
any
engine accessory that
interferes with
filter
gasket (8)
with a thin
coating of
Dow Corning
removal of
the adapter.
Compound,
DC-4, apply by brushing
or wiping lubri-
cant on to base gasket. b. Note angular position of adapter (3), then re-
e. Install spin-on filter, (6), on the stud and torque move safety wire and loosen adapter nut (2).
to 18-20 lb-ft or 3/4 to 1 full turn after gasket c. Unscrew adapter and remove from engine. Dis-
makes contact. card adapter O-ring (1).
f. Safety
wire filter
to adapter.
g. Install all parts removed
for access and service
11-52. DISASSEMBLY,
INSPECTION,
AND REASSEM-
the engine with the proper
grade and quantity
of en- BLY. Figure
11-5 shows the relative
position of the
gine oil.
One additional
quart of oil is
required each
internal parts
of the filter
adapter and may
be used
time the filter element is changed.
as a guide during installation
of parts.
11-20

Cessna T182 Series Specifications

General

Engine Type	Lycoming IO-540-AB1A5
Horsepower	230 hp
Seating Capacity	4
Service Ceiling	18, 100 feet
Takeoff Distance	1, 600 feet
Landing Distance	1, 350 ft
Type	Single-engine
Max Takeoff Weight	3, 100 lb
Wingspan	36 ft
Length	29 ft
Height	9 feet 3 inches
Fuel Capacity	92 US gal (348 L)