Cessna T182 Series User Manual

MODEL
182
&
T182
SERIES
SERVICE
MANUAL
Before
assembly,
place
a straightedge
across
the
Cessna
Supply
Division.
or one
may
be
bottom
of
filter
can.
Check
for distortion
or
fabricated
as
shown
in figure
11-5.
Remove
out-of-flat
condition
greater
than
0. 010 inch.
any engine
accessory
that
interferes
with
Install
a new
filter
can if
either of
these
con-
removal
of the
adapter.
ditions
exist.
b. Note angular
position
of adapter
(9),
then re-
After
installing
a
new gasket
on
lid, turn
lid
move
safety
wire and
loosen
adapter
nut
(10).
over.
If
gaskets
falls,
try a
different
gasket
c.
Unscrew
adapter
and
remove
from
engine.
Dis-
and repeat
test.
If
this gasket
falls
off,
in-
card
adapter
O-ring
(11).
stall a
new lid.
11-45.
DISASSEMBLY,
INSPECTION
AND
REASSEM-
g.
Inspect
the
adapter
gasket
seat
for
gouges,
deep
BLI.
Figure
11-3
shows
the relative
position
of
the
scratches,
wrench
marks
and
mutilation.
If any
of
internal
parts of
the filter
adapter
and
may
be used
these
conditions
are
found,
install
a
new
adapter.
as a
guide
during
installation
of parts.
The bypass
h.
Place
a new
filter
element
(5) in
can (4)
and
in-
valve
is
to be
installed
as a complete
unit,
with
the
sert
the
hollow
stud (1)
with
a new
metal gasket
(2)
valve
being
staked
in three
places.
The heli-coil
type
in place,
through
the filter
can
and element.
insert
(14)
in the
adapter
may be
replaced,
although
i. Position
a new
gasket
(6) inside
flange
of
lid (7)
special
tools
are required.
Follow
instructions
of
and
place lid
in position
on filter
can.
the tool
manufacturer
for
their use.
Inspect
threads
j.
With new
gasket
(8) on
face of
lid, install
filter
on adapter
and
in engine
for damage.
Clean
adapter
can
assembly
on
adapter
(9). While
holding
filter
in solvent
and
dry
with compressed
air.
Ascertain
can
to prevent
turning,
tighten
hollow
stud
(1) and
that
all
passages
in
the
adapter
are
open
and free
of
torque
to
20-25
lb-ft
(240-300
lb-in),
using
a torque
foreign
material.
Also,
check
that
bypass
valve
is
wrench.
seated
properly.
k. Install
all
parts
removed
for
access
and
service
the
engine
with
the
proper
grade
and
quantity
of
en-
gine
oil.
One
additional
quart
of
oil is
required
each
11-46.
INSTALLATION.
time
the
filter
element
is changed.
a. Assemble
adapter
nut (10)
and
new
O-ring
(11)
l.
Start
engine
and
check
for proper
oil
pressure.
on
adapter
(9)
in sequence
illustrated
in figure
11-3.
Check
for
oil
leakage
after
warming
up
the engine.
b.
Lubricate
O-ring
on adapter
with
clean
engine
m.
Again
check
for
oil
leakage
after
engine
has been
oil.
Tighten
adapter
nut until
O-ring
is centered
in
run
at high
power
setting
(preferably
a
flight
around
its
groove
on the
adapter.
the
field).
c.
Apply
anti-seize
compound
sparingly
to the
n.
Check
to make
sure
filter
can
has
not
been
mak-
adapter
threads,
then
simultaneously
screw
adapter
ing
contact
with
any adjacent
parts
due
to engine
and
adapter
nut
into
engine
until
O-ring
seats
against
torque.
engine
boss
without
turning
adapter
nut
(10).
Rotate
o.
While
engine
is
still
warm,
recheck
torque
on
adapter
to approximate
angular
position
noted
during
hollow
stud
(1),
then
safety
stud
to lower
tab
(3)
on
removal.
Do not
tighten
adapter
nut at
this
time.
filter
can
and safety
adapter
(9) to
upper
tab
on
fil-
d.
Temporarily
install
filter
assembly
on
adapter,
ter can.
and
position
so
adequate
clearance
with adjacent
parts
is attained.
Maintaining
this
position
of
the adapter,
11-43.
FILTER
ADAPTER.
tighten
adapter
nut
to 50-60
lb-ft
(600-700
lb-in)
and
safety.
Use
a torque
wrench,
extension
and
adapter
11-44.
REMOVAL.
(See
figure
11-3.)
as necessary
when
tightening
adapter
nut.
a.
Remove
filter
assembly
in accordance
with
para-
e.
Using
new
gaskets,
install
filter
assembly
as
graph
11-38.
outlined
in paragraph
11-42.
Be sure
to
service
the
engine
oil
system.
NOTE
A special
wrench
adapter
for
adapter
nut
(10)
(Part
No.
SE-709)
is
available
from
SHOP
NOTES:
11-19

Cessna T182 Series Specifications

General

Engine Type	Lycoming IO-540-AB1A5
Horsepower	230 hp
Seating Capacity	4
Service Ceiling	18, 100 feet
Takeoff Distance	1, 600 feet
Landing Distance	1, 350 ft
Type	Single-engine
Max Takeoff Weight	3, 100 lb
Wingspan	36 ft
Length	29 ft
Height	9 feet 3 inches
Fuel Capacity	92 US gal (348 L)