Chroma 16502 - Setting Up Binning Tests

Description of Panel
4-11
<
M
A I N I N D E X
：
B I N N I N G >
S E T T I N G
C O U N T
← Condition setting
F2
F3
F4
←
Counter
F1
Press [F1] to enter setting screen as below shown:
< B I N N I N G S E
T
>
D I G I T U P
N O
M
I
N A L ： 0 0 0
. 0
0 0
0
Ω
D I G I T D O
W
N
D I G I T
P r e s s d
o
w
n
a
r r
o w t o
s e t b i n s
P r e s s
M
A I N I N
D E X
t
o
e x
i t V I E W
←
The cursor positioned number digit
up.
F2
←
The cursor positioned number digit
down.
F3
←
The cursor move right.
F4
←
Display high/low limit of binning set.
F1
Assumed NOMINAL is set to 100mΩ, BIN1∼BIN8 set as ±0.1%∼±0.8%, please follows the
below method to operate:
(1) Press [F3] key to move the cursor to NOMINAL position, and move the cursor to
hundred then press [F1] key to adjust the number to 1. Press [F3] key to move the
cursor to (-) position, then press [F1] key to set unit to m.
After the setting is completed the screen should be as below shown:
< B I N N I N G S E T >
D I G I T U P
N O
M
I N A L ： 1 0 0
. 0 0 0 0
m
Ω
D I G I T D O
W
N
D I G I T
P r e s s d o
w
n
a
r r
o w t o
s e t b i n s
P r e s s
M
A I N I N D E X t o e x i t V I E W
F2
F3
F4
F1
(2) Press [F4] key, the screen switched as below shown.
< B I N N I N G S
E T >
B I N
H
I L O D I G I T U P
- - - - - - - - - - - - - - - - - -
- - - -
- - - - - - - -
1 0 0 0
. 0 0
0 0
Ω 0
0 0
. 0 0 0 0
Ω D I G I T D O
W
N
2 0 0 0
.
0 0 0
0
Ω 0 0
0
. 0 0 0 0
Ω
3 0 0 0
. 0 0 0 0
Ω 0 0 0
. 0 0 0 0
Ω D I G I T
4 0 0 0
. 0 0 0 0
Ω 0 0 0
. 0 0 0 0
Ω
P r e s s
M
A I N I N D E X t o e x i t
M
O D E ： A B S
Notice: The high/low values of percentage and
absolute modes can’t convert for each other.
F2
F3
F4
← Set the high/low limits are ABS
(absolute value) or %(percentage)
F1
(3) Press [F3] key, the cursor move to the first decimal place of high limit (HI) of BIN 1.
Press [F1] key, digit up to 1 and then press [TRIGGER] make low limit (LO) change to –
0.1% by high limit (HI) value. Press [] key to move the cursor to BIN2. According to
setting method of BIN1 to change BIN2 setting value as ±0.2%, BIN3 and BIN8 are
deduced by analogy.
<<If the values of high limit (HI) and low limit (LO) are not symmetry. Please
set high limit (HI) firstly, press [

] key to move the cursor to LO field and then
set low limit (LO).>>
After the setting is completed the screen as the below shown.