Cisco SCE 8000

B-7
Cisco SCE8000 GBE Installation and Configuration Guide
Appendix B CLI Commands to Verify a Successful Installation
CLI Command Output Samples
show inventory
Look for the following lines:
• All lines containing the text ‘NAME: "SCE8000 optic’. There should be one line for each installed
optic.
SCE8000> show inventory
NAME: "SCE8000 Chassis", DESCR: "SCE8000"
PID: SCE8000 , VID: V01, SN: FOX1232G00V
NAME: "SCE8000 Service Control Module (SCM) in slot 1", DESCR: "SCE8000-SCM-E"
PID: SCE8000-SCM-E , VID: V01, SN: CAT1231G040
NAME: "SCE8000 SPA Interface Processor (SIP) in slot 3", DESCR: "SCE8000-SIP"
PID: SCE8000-SIP , VID: V01, SN: CAT1229G03H
NAME: "SCE8000 SPA module 3/0", DESCR: "SPA-1X10GE-L-V2"
PID: SPA-1X10GE-L-V2 , VID: V02, SN: JAE1229PFVA
NAME: "SCE8000 SPA module 3/1", DESCR: "SPA-1X10GE-L-V2"
PID: SPA-1X10GE-L-V2 , VID: V02, SN: JAE1229PFR4
NAME: "SCE8000 SPA module 3/2", DESCR: "SPA-1X10GE-L-V2"
PID: SPA-1X10GE-L-V2 , VID: V02, SN: JAE1229PFR6
NAME: "SCE8000 SPA module 3/3", DESCR: "SPA-1X10GE-L-V2"
PID: SPA-1X10GE-L-V2 , VID: V02, SN: JAE1229PFR2
NAME: "SCE8000 FAN 1", DESCR: "SCE8000-FAN"
PID: SCE8000-FAN , VID: V01, SN: DCH12281410
NAME: "SCE8000 AC power supply 0", DESCR: "PWR-2700-AC/4"
PID: PWR-2700-AC/4 , VID: V02, SN: APS12160003
NAME: "SCE8000 AC power supply 1", DESCR: "PWR-2700-AC/4"
PID: PWR-2700-AC/4 , VID: V02, SN: APS1216002N
NAME: "SCE8000 optic 3/0/0", DESCR: "XFP-10GLR-OC192SR "
PID: XFP-10GLR-OC192SR , VID: V02, SN: ONT121110LJ
NAME: "SCE8000 optic 3/1/0", DESCR: "XFP-10GLR-OC192SR "
PID: XFP-10GLR-OC192SR , VID: V02, SN: ECL122201CD
NAME: "SCE8000 optic 3/2/0", DESCR: "XFP-10GLR-OC192SR "
PID: XFP-10GLR-OC192SR , VID: V02, SN: ECL122201CJ
NAME: "SCE8000 optic 3/3/0", DESCR: "XFP-10GLR-OC192SR "
PID: XFP-10GLR-OC192SR , VID: V02, SN: ECL122103BA
show interface
Run this command for each interface. The command syntax is:
show interface TenGigabitEthernet 3/bay-number/0
SCE8000> show interface TenGigabitEthernet 3/0/0
Auto negotiation configured: Disabled
Actual status:
Link is: ON
Auto negotiation: Disabled
Bandwidth (L1): 10000000 Kbps, Burst-size: 50000 bytes
Pseudo IP Address: Not Configured