DAELIM ROADWIN VJ125 - Primary Drive Gear Installation; R. Crankcase Cover Installation

7-11
CLUTCH/GEARSHIFT
WOODRUFF KEY
WOODRUFF KEY
WOODRUFF KEY
WOODRUFF KEY
WOODRUFF KEY
WOODRUFF KEY
WOODRUFF KEY
WOODRUFF KEY
WOODRUFF KEY
WOODRUFF KEY
WOODRUFF KEY
WOODRUFF KEY
WOODRUFF KEY
WOODRUFF KEY
WOODRUFF KEY
WOODRUFF KEY
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK WASHER
LOCK WASHER
LOCK WASHER
LOCK WASHER
LOCK WASHER
LOCK WASHER
LOCK WASHER
LOCK WASHER
LOCK WASHER
LOCK WASHER
LOCK WASHER
LOCK WASHER
LOCK WASHER
LOCK WASHER
LOCK WASHER
LOCK WASHER
EXTENSION BAR
EXTENSION BAR
EXTENSION BAR
EXTENSION BAR
EXTENSION BAR
EXTENSION BAR
EXTENSION BAR
EXTENSION BAR
EXTENSION BAR
EXTENSION BAR
EXTENSION BAR
EXTENSION BAR
EXTENSION BAR
EXTENSION BAR
EXTENSION BAR
EXTENSION BAR
EXTENSION BAR
EXTENSION BAR
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT WRENCH 20X24mm
LOCK NUT WRENCH 20X24mm
LOCK NUT WRENCH 20X24mm
LOCK NUT WRENCH 20X24mm
LOCK NUT WRENCH 20X24mm
LOCK NUT WRENCH 20X24mm
LOCK NUT WRENCH 20X24mm
LOCK NUT WRENCH 20X24mm
LOCK NUT WRENCH 20X24mm
LOCK NUT WRENCH 20X24mm
LOCK NUT WRENCH 20X24mm
LOCK NUT WRENCH 20X24mm
LOCK NUT WRENCH 20X24mm
LOCK NUT WRENCH 20X24mm
LOCK NUT WRENCH 20X24mm
LOCK NUT WRENCH 20X24mm
LOCK NUT WRENCH 20X24mm
LOCK NUT WRENCH 20X24mm
INSTALLATION
● Install the woodruff key into the key groove of the
crankshaft.
● Align the primary drive gear key groove with the
crankshaft key and install the gear.
● Install the lock washer.
● Coat the nut with clean engine oil, and temporarily
tighten the lock nut.
● Hold the flywheel with a flywheel holder, and
tighten the primary drive gear lock nut with the
specified torque.
TORQUE : 6.5kgf
··
m(65N
··
m)
TOOLS : FLYWHEEL HOLDER
LOCK NUT WRENCH, 20
××
24mm
EXTENSION BAR
R. CRANKCASE COVER
INSTALLATION
● Remove the gasket from the crankcase surface.
● Install the two dowel pins and a new gasket.
DOWEL PINS
DOWEL PINS
DOWEL PINS
DOWEL PINS
DOWEL PINS
DOWEL PINS
DOWEL PINS
DOWEL PINS
DOWEL PINS
DOWEL PINS
DOWEL PINS
DOWEL PINS
DOWEL PINS
DOWEL PINS
DOWEL PINS
DOWEL PINS
DOWEL PINS
DOWEL PINS