Danfoss H1 User Manual (English)

Other manuals for Danfoss H1

Service Manual72 pages

Basic Information40 pages

Questions and Answers:

R
Rhonda JohnsonAug 16, 2025
What to do if Danfoss H1 Water Pump transmission operates normally in one direction only?
- L
  Lori DavisAug 16, 2025
  If your Danfoss Water Pump transmission operates normally in only one direction, the issue could stem from several causes. The input to the control module might be operating improperly; check the control input and repair or replace it as necessary. Control orifices or screens could be blocked; clean the orifices and clean or replace the screens. Interchanging the charge check/HPRVs can help determine if the problem is valve-related; if the problem changes direction, replace the valve that doesn't operate correctly. Low or decaying servo pressure is another possibility; check for damaged servo seals, replace them, and retest.
R
Reginald MitchellAug 19, 2025
Why Danfoss H1 Water Pump control operates the pump in one direction only?
- S
  samantha26Sep 12, 2025
  If your Danfoss Water Pump control operates the pump in only one direction, it could be due to control coil failure. Measure the resistance at the coil pins; it should be 14.2W (24V) or 3.66W (12V) at 20° C [70° F]. If it's not, replace the coil.
S
Shelby RamirezAug 22, 2025
What to do if Danfoss H1 has erratic or no machine function?
- D
  Dennis BarrettAug 22, 2025
  If your Danfoss Water Pump is showing erratic or no machine function, it could be due to an external controller malfunction or a hydraulic system problem. To check for a controller issue, verify the external controller problem using a spare controller and replace it if necessary. Also, check the hydraulic system fluid level, pressures, filters, and address any hydraulic system problems.
J
jason74Aug 28, 2025
What to do if Danfoss H1 system has noise or vibration?
- D
  Daniel AnthonyAug 28, 2025
  If your Danfoss Water Pump system is experiencing noise or vibration, several issues could be the cause. Low oil level can lead to cavitation, so start by filling the reservoir. Air in the system can also cause noise, foaming, and hot oil; locate and repair where air is entering, and ensure the inlet line isn't restricted and is the proper size. Cold oil may be too viscous, causing the pump to cavitate; allow the oil to warm up at idle speed. A high inlet vacuum can also cause noise/cavitation; check the inlet line and filter. Other potential causes include a loose input shaft coupling (replace it), misaligned shafts (correct the misalignment), or sticking valves (clean/replace them). If the noise is unusual, contamination may be present.
J
Jenny ParkSep 2, 2025
What to do if Danfoss Water Pump system will not operate in either direction?
- V
  victoriajimenezSep 2, 2025
  If your Danfoss Water Pump system isn't operating in either direction, it could be due to insufficient hydraulic fluid; ensure the reservoir is filled to the proper level. Another possibility is blocked control orifices or screens; clean the control orifices and clean or replace the control screens.
S
Sara SmithSep 6, 2025
What to do if I can't find neutral on my Danfoss H1?
- B
  bcrawfordSep 6, 2025
  If you're having trouble finding neutral on your Danfoss Water Pump, first disconnect the input to the control module and see if the pump returns to neutral. If it does, there's an input fault, so replace or repair the external controller. If not, shunt servo gauge ports M4 and M5 together with an external hose and see if the pump returns to neutral. If yes, the control neutral is improperly set. If no, balance the swashplate. If you still cannot set neutral, replace control.
J
Jacqueline BarnesSep 8, 2025
Why is there no pump function in my Danfoss Water Pump?
- N
  nataliesawyerSep 9, 2025
  If there is no pump function in your Danfoss Water Pump, it could be due to no power to the controller. Restore power to the controller.
C
Cathy HawkinsSep 12, 2025
Why is my Danfoss H1 function erratic?
- M
  maysandreaSep 12, 2025
  If your Danfoss Water Pump is functioning erratically, the electrical connection to the pump might be bad. Disconnect the connection, check the wires, and then reconnect them.