Back-channel duct kit, D4h Duct kit that converts enclosure to either in-bottom/out-top venting
or top only venting. Enclosure size: 2000 mm (78.7 in).
176F3630
Pedestal, D1h Provides a 400 mm (15.7 in) pedestal that allows the drive to be oor
mounted. The front of the pedestal has openings for input air to cool
the power components.
176F3631
Pedestal, D2h Provides a 400 mm (15.7 in) pedestal that allows the drive to be oor
mounted. The front of the pedestal has openings for input air to cool
the power components.
176F3632
Pedestal, D5h/D6h Provides a 200 mm (7.9 in) pedestal that allows the drive to be oor
mounted. The front of the pedestal has openings for input air to cool
the power components.
176F3452
Pedestal, D7h/D8h Provides a 200 mm (7.9 in) pedestal that allows the drive to be oor
mounted. The front of the pedestal has openings for input air to cool
the power components.
176F3539
Top entry of eldbus cables,
D1h–D8h
Allows for the installation of eldbus cables through the top of the
drive. The kit is IP20/chassis when installed, but a dierent mating
connector can be used to increase the protection rating.
176F3594
USB in the door, D1h–D8h
(IP20/chassis)
USB extension cord kit to allow access to the drive controls via laptop
computer without opening the drive.
Contact factory
USB in the door, D1h–D8h
(IP21/Type 1 and IP54/Type 12)
USB extension cord kit to allow access to the drive controls via laptop
computer without opening the drive.
Contact factory
Input plate option, D1h–D8h Allows fuses, disconnect/fuses, RFI, FRI/fuses, and RFI/disconnect/fuses
options to be added.
Contact factory
Terminal blocks Screw terminal blocks for replacing spring loaded terminals.
(1 pc 10 pin 1 pc 6 pin and 1 pc 3-pin connectors)
130B1116
Back-channel cooling kits Standard Stainless steel
In-back/out-back (Non-Rittal
enclosures), D3h
Allows the cooling air to be directed in and out through the back of
the drive. Does not include plates for mounting in the enclosure. This
kit is used only for enclosure D3h.
176F3519 176F3520
In-back/out-back (Non-Rittal
enclosures), D4h
Allows the cooling air to be directed in and out through the back of
the drive. Does not include plates for mounting in the enclosure. This
kit is used only for enclosure D4h.
176F3524 176F3525
In bottom/out back, D1h/D3h Allows the cooling air to be directed in through the bottom and out
through the back of the drive. This kit is used only for enclosures
D1h/D3h.
176F3522 176F3523
In bottom/out back, D2h/D4h Allows the cooling air to be directed in through the bottom and out
through the back of the drive. This kit is used only for enclosures
D2h/D4h.
176F3527 176F3528
In back/out back, D1h Allows the cooling air to be directed in and out through the back of
the drive. This kit is used only for enclosure D1h.
176F3648 176F3656
In back/out back, D2h Allows the cooling air to be directed in and out through the back of
the drive. This kit is used only for enclosure D2h.
176F3649 176F3657
In back/out back, D3h Allows the cooling air to be directed in and out through the back of
the drive. This kit is used only for enclosure D3h.
176F3625 176F3654
In back/out back, D4h Allows the cooling air to be directed in and out through the back of
the drive. This kit is used only for enclosure D4h.
176F3626 176F3655
In back/out back, D5h/D6h Allows the cooling air to be directed in and out through the back of
the drive. This kit is used only for enclosures D5h/D6h.
176F3530 –
In back/out back, D7h/D8h Allows the cooling air to be directed in and out through the back of
the drive. This kit is used only for enclosures D7h/D8h.
176F3531 –
LCP
LCP 101 Numerical local control panel (NLCP). 130B1124
LCP 102 Graphical Local control panel (GLCP). 130B1107
LCP cable Separate LCP cable, 3 m (9 ft). 175Z0929
How to Order a Drive VLT® AutomationDrive FC 302
198 Danfoss A/S © 01/2018 All rights reserved. MG38C202
1313
To Next Page
Loading...
