Datakom D-200 MK2 - 4.2. COMMON TOPOLOGY DIAGRAMS

135 pages

To Next Page

To Previous Page

D-200 MK2 User Manual Firmware V-6.3

L058D01-EN - 30 -

4.3. 3 PHASE, 3 WIRE, DELTA

4.2. 3 PHASE, 4 WIRE, STAR

Main Page

Table of Contents6
Installation Instructions10
Mounting11
Dimensions11
Sealing, Gasket14
Electrical Installation15
Terminal Descriptions16
Battery Voltage Input16
Ac Voltage Inputs17
Ac Current Inputs18
Digital Inputs21
Analog Sender Inputs and Sender Ground21
Charge Input Terminal22
Magnetic Pickup Input22
Mains Contactor Output23
Generator Contactor Output23
Digital Outputs23
Port (Plug-In Module)24
J1939-Canbus Port (Optional)25
Usb Device Port25
Gsm Modem (Plug-In Module)26
Ethernet Port (Plug-In Module)27
Wi-Fi (Plug-In Module)28
Topologies29
Selecting the Topology29
Phase, 4 Wire, Star30
Phase, 3 Wire, Delta30
Phase, 4 Wire, Delta31
Phase, 3 Wire, Delta, 2 Ct (L1-L2)31
Phase, 3 Wire, Delta, 2 Ct (L1-L3)32
PHASE, 3 WIRE, DELTA, 2 Cts (L1-L2)32
PHASE, 3 WIRE, DELTA, 2 Cts (L1-L3)33
Phase, 2 Wire33
Functionalities34
Ct Location Selection34
Amf Functionality34
Ats Functionality34
Remote Start Functionality34
Engine Controller Functionality35
400Hz Operation36
Connection Diagrams37
AMF FUNCTIONALITY, Cts at LOAD SIDE37
AMF FUNCTIONALITY, Cts at ALTERNATOR SIDE38
Ats Functionality39
Remote Start Functionality40
Engine Control Functionality41
Terminal Description43
Technical Specifications45
Description of Controls46
Front Panel Functionality46
Pushbutton Functions47
Display Screen Organization48
Automatic Display Scroll49
Measured Parameters50
Led Lamps51
Waveform Display & Harmonic Analysis52
Displaying Event Logs54
Statistical Counters56
Fuel Filling Counter56
Fuel Consumption Monitoring57
Operation of the Unit58
Quick Start Guide58
Stop Mode58
Auto Mode59
Run Mode60
Test Mode60
Protections and Alarms61
Disabling All Protections62
Service Request Alarm62
Shutdown Alarms63
Loaddump Alarms64
Warnings65
Non-Visual Warnings67
Programming68
Resetting to Factory Defaults68
Entering the Programming Mode69
Navigating between Menus70
Modifying Parameter Value71
Programming Mode Exit71
Program Parameter List72
Controller Configuration Group72
Electrical Parameters Group77
Engine Parameters Group84
Adjust Date and Time91
Weekly Operation Schedule91
Exerciser Schedule92
Sender Configuration93
Digital Input Configuration95
Output Configuration97
Site ID String99
Engine Serial Number99
Modem1-2/Sms1-2-3-4 Telephone Numbers99
Gsm Modem Parameters100
Tcp/Ip Parameters101
Wi-Fi PARAMETERS102
Ethernet Configuration103
Wi-Fi CONFIGURATION104
Gsm Configuration105
Crank Cutting106
Overcurrent Protection (Idmt)107
Motorized Circuit Breaker Control109
J1939 Canbus Engine Support (Optional)111
Sms Commands115
Software Features117
Load Shedding / Dummy Load117
Load Add / Substract118
Five Step Load Management119
Remote Start Operation120
Disable Auto Start, Simulate Mains120
Battery Charging Operation, Delayed Simulate Mains121
Dual Genset Mutual Standby Operation122
Multiple Voltage and Frequency123
Single Phase Operation123
External Control of the Unit123
Automatic Exerciser124
Weekly Operation Scheduler124
Engine Heating Operation125
Engine Idle Speed Operati̇on125
Engine Block Heater125
Fuel Pump Control126
Gas Engine Fuel Solenoid Control126
Pre-Transfer Signal126
Charging the Engine Battery127
Externally Controlled Digital Outputs127
Combat Mode127
Resetting the Controller128
Zero Power at Rest128
Modbus Communications129
Parameters Required for Rs-485 Modbus Operation130
Data Formats130
Declaration of Conformity133
Maintenance133
Disposal of the Unit133
Rohs Compliance133
Troubleshooting Guide134

Datakom D-200 MK2 - 4.2. COMMON TOPOLOGY DIAGRAMS

Table of Contents

Related product manuals