Datakom D-500 - Remote Start Functionality

153 pages

Save Page as PDF

To Next Page

To Previous Page

D-500 User Manual Rev_06 Firmware V-5.8

K35D05-EN - 45 -

6.4. REMOTE START FUNCTIONALITY

Main Page

Table of Contents6
Installation Instructions11
Mounting12
Dimensions12
Sealing, Gasket15
Electrical Installation16
Terminal Descriptions17
Battery Voltage Input17
Ac Voltage Inputs18
Ac Current Inputs19
Digital Inputs22
Analog Sender Inputs and Sender Ground22
Charge Input Terminal23
Magnetic Pickup Input23
Mains Contactor Output24
Generator Contactor Output24
Digital Outputs24
Input/Output Extension25
Port26
J1939-Canbus Port26
Ethernet Port27
Usb Device Port28
Usb Host Port (Optional)29
Port (Optional)30
Micro-Sd Memory Card Slot (Optional)31
Gsm Modem (Optional)32
Topologies34
Selecting the Topology34
Phase, 4 Wire, Star35
Phase, 3 Wire, Delta35
Phase, 4 Wire, Delta36
Phase, 3 Wire, Delta, 2 Ct (L1-L2)36
Phase, 3 Wire, Delta, 2 Ct (L1-L3)37
PHASE, 3 WIRE, DELTA, 2 Cts (L1-L2)37
PHASE, 3 WIRE, DELTA, 2 Cts (L1-L3)38
Phase, 2 Wire38
Functionalities39
Ct Location Selection39
Amf Functionality39
Ats Functionality39
Remote Start Functionality39
Engine Controller Functionality40
Remote Display Unit Functionality41
400Hz Operation41
Connection Diagrams42
AMF FUNCTIONALITY, Cts at LOAD SIDE42
AMF FUNCTIONALITY, Cts at ALTERNATOR SIDE43
Ats Functionality44
Remote Start Functionality45
Engine Control Functionality46
Remote Display Panel Functionality47
Terminal Description48
Technical Specifications51
Description of Controls52
Front Panel Functionality52
Pushbutton Functions53
Display Screen Organization54
Automatic Display Scroll55
Measured Parameters57
Led Lamps58
Waveform Display & Harmonic Analysis59
Displaying Event Logs61
Statistical Counters63
Fuel Filling Counter63
Fuel Consumption Monitoring64
Operation of the Unit65
Quick Start Guide65
Stop Mode65
Auto Mode66
Run Mode, Manual Control67
Test Mode67
Protections and Alarms68
Disabling All Protections69
Service Request Alarm69
Shutdown Alarms70
Loaddump Alarms71
Warnings72
Non-Visual Warnings74
Programming75
Resetting to Factory Defaults75
Entering the Programming Mode76
Navigating between Menus77
Modifying Parameter Value78
Programming Mode Exit78
Program Parameter List79
Controller Configuration Group79
Electrical Parameters Group86
Engine Parameters Group93
Adjust Date and Time100
Weekly Operation Schedule100
Exerciser Schedule101
Sender Configuration102
Digital Input Configuration104
Output Configuration106
Site ID String108
Engine Serial Number108
Modem1-2/Sms1-2-3-4 Telephone Numbers108
Gsm Modem Parameters109
Ethernet Parameters110
Sntp Parameters112
Synchronization Parameters112
Crank Cutting113
Overcurrent Protection (Idmt)114
Motorized Circuit Breaker Control116
J1939 Canbus Engine Support118
Gps Support122
Ethernet Configuration124
Gsm Configuration124
Dynamic Dns Feature124
Accessing the Embedded Web Server124
Web Monitoring and Control of Gensets124
Central Monitoring of Gensets124
E-Mail Sending124
Sms Commands125
Load Transfer Modes127
Transfer with Interruption127
Uninterrupted Transfer128
Data Recording129
Data Recording Media129
Directory Structure130
Understanding the Csv Format130
Recorded Data List, Record Period131
Software Features132
Load Shedding / Dummy Load132
Load Add / Substract133
Five Step Load Management134
Remote Start Operation135
Disable Auto Start, Simulate Mains135
Battery Charging Operation, Delayed Simulate Mains136
Dual Genset Mutual Standby Operation137
Multiple Voltage and Frequency138
Single Phase Operation138
External Control of the Unit138
Automatic Exerciser139
Weekly Operation Scheduler139
Engine Heating Operation140
Engine Idle Speed Operati̇on140
Engine Block Heater140
Fuel Pump Control141
Gas Engine Fuel Solenoid Control141
Pre-Transfer Signal141
Charging the Engine Battery142
Externally Controlled Digital Outputs142
Combat Mode142
Resetting the Controller143
Automatic Connection Topology Determination143
Zero Power at Rest144
Modbus Communications145
Parameters Required for Rs-485 Modbus Operation146
Parameters Required for Modbus-Tcp/Ip Via Ethernet146
Data Formats146
Snmp Communications149
Snmp Trap Messages150

Datakom D-500 - Remote Start Functionality

Table of Contents

Other manuals for Datakom D-500

Related product manuals