Datakom D-700 MK3 - Remote Display Panel Functionality

218 pages

Save Page as PDF

To Next Page

To Previous Page

D-700 MK3 User Manual Firmware V-16.8

- 71 -

7.9. REMOTE DISPLAY PANEL FUNCTIONALITY

Main Page

Table of Contents6
Installation Instructions12
Mounting13
Dimensions13
Sealing, Gasket16
Electrical Installation17
Terminal Descriptions18
Battery Voltage Input18
Ac Voltage Inputs19
Ac Current Inputs20
Digital Inputs23
Analog Sender Inputs and Sender Ground23
Charge Input Terminal24
Magnetic Pickup Input24
Digital Outputs25
Input/Output Expansion26
J1939-Canbus Port27
Usb Device Port27
Plug-In Modules28
Modem Plug-In Module29
Gsm Modem Module29
Wi-Fi MODULE31
Ethernet Module32
Module33
Synchronization Plug-In Module35
Analog Avr Control Output35
Analog Governor Control Output35
Datalink-Canbus Port36
Analog Load Share Signal37
Analog Plug-In Module37
Analog I/O Expansion Module37
DC Voltage & Current Module38
Mains Ct Inputs Module39
Communication Module40
Ethernet Port40
Usb Host Port41
Port42
Plug-In Module43
Module43
Gsm Modem Module44
Wi-Fi MODULE46
Ethernet Module47
Module48
Topologies49
Selecting the Topology49
Phase, 4 Wire, Star50
Phase, 3 Wire, Delta50
Phase, 4 Wire, Delta51
Phase, 3 Wire, Delta, 2 Ct (L1-L2)51
Phase, 3 Wire, Delta, 2 Ct (L1-L3)52
PHASE, 3 WIRE, DELTA, 2 Cts (L1-L2)52
PHASE, 3 WIRE, DELTA, 2 Cts (L1-L3)53
Phase, 2 Wire53
Functionalities54
Ct Location Selection54
Synchronization Functionality55
Mains Synchronization Functionality56
Single Genset Parallel with Mains57
DC Genset Functionality57
Amf Functionality58
Ats Functionality58
Remote Start Functionality59
Engine Controller Functionality60
Remote Display Unit Functionality61
400Hz Operation62
Connection Diagrams63
Genset Synchronization Functionality63
Mains Synchronization Functionality64
DC Genset Functionality66
Amf Functionality67
Ats Functionality68
Remote Start Functionality69
Engine Control Functionality70
Remote Display Panel Functionality71
Terminal Description72
Technical Specifications77
Description of Controls78
Front Panel Functionality78
Pushbutton Functions79
Display Screen Organization81
Automatic Display Scroll82
Measured Parameters84
Led Lamps85
Waveform Display & Harmonic Analysis86
Displaying Event Logs88
Statistical Counters90
Fuel Filling Counter90
Fuel Consumption Monitoring91
Operation of the Unit92
Quick Start Guide92
Stop Mode92
Auto Mode93
Run Mode, Manual Control94
Test Mode95
Protections and Alarms96
Disabling All Protections97
Service Request Alarm97
Shutdown Alarms98
Loaddump Alarms99
Warnings101
Non-Visual Warnings103
Programming104
Resetting to Factory Defaults104
Entering the Programming Mode105
Navigating between Menus106
Modifying Parameter Value107
Programming Mode Exit108
Program Parameter List109
Controller Configuration Group109
Electrical Parameters Group116
Engine Parameters Group124
Adjust Date and Time132
Weekly Operation Schedule133
Exerciser Schedule134
Sender Configuration135
Digital Input Configuration137
Output Configuration139
Site ID String141
Engine Serial Number141
Modem1-2/Sms1-2-3-4 Telephone Numbers141
Gsm Modem Parameters142
Tcp/Ip Parameters143
Sntp Parameters145
Wi-Fi PARAMETERS145
Synchronization Parameters146
DC Genset Parameters153
Snmp Parameters155
Ethernet Configuration156
Wi-Fi CONFIGURATION157
Gsm Configuration158
Crank Cutting159
Overcurrent Protection (Idmt)160
Motorized Circuit Breaker Control162
Auto Learning164
Speed & Voltage Up/Down Relay Outputs167
Speed Up/Down Control167
Voltage Up/Down Control167
J1939 Canbus Engine Support168
Dpf Regeneration Support172
DC Genset Operation173
Optimal Charging with Variable Speed173
Uncontrolled Charging with Fixed Speed Operation175
Gps Support177
Sms Commands179
Load Transfer Modes181
Transfer with Interruption181
Uninterrupted Transfer182
Soft Transfer183
Load Sharing184
Digital Load Sharing (Datalink)185
Analog Load Sharing186
Droop Mode Operation187
Peak Lopping188
Power Export to Mains189
Distributed Power Export to Mains190
Peak Lopping with Genset Priority191
Protection Functions Paralleling with Mains192
ROCOF FUNCTION (Rate of Change of Frequency)192
Vector Shift Function192
Over/Under Frequency Function193
Over/Under Voltage Function193
Mains Reverse Power Function193
Frequency Function193
Data Recording194
Data Recording Media194
Directory Structure195
Understanding the Csv Format195
Recorded Data List, Record Period196
Software Features197
Load Shedding / Dummy Load197
Load Add / Substract198
Five Step Load Management199
Remote Start Operation200
Disable Auto Start, Simulate Mains200
Battery Charging Operation, Delayed Simulate Mains201
Dual Genset Mutual Standby Operation202
Multiple Voltage and Frequency203
Single Phase Operation203
External Control of the Unit203
Automatic Exerciser204
Weekly Operation Scheduler204
Engine Heating Operation205
Engine Idle Speed Operati̇on205
Engine Block Heater205
Fuel Pump Control206
Gas Engine Fuel Solenoid Control206
Pre-Transfer Signal206
Charging the Engine Battery207
Externally Controlled Digital Outputs207
Combat Mode207
Resetting the Controller208
Automatic Connection Topology Determination208
Zero Power at Rest209
Modbus Communications210
Parameters Required for Rs-485 Modbus Operation211
Parameters Required for Modbus-Tcp/Ip Via Ethernet211
Data Formats211
Snmp Communications214
Parameters Required for Snmp Via Ethernet215
Snmp Trap Messages215
Declaration of Conformity216
Maintenance216
Disposal of the Unit216
Rohs Compliance216
Troubleshooting Guide217

Datakom D-700 MK3 - Remote Display Panel Functionality

Table of Contents

Related product manuals