Datalogic Gryphon L GD4300 User Manual

Gryphon™ Family
General Purpose Handheld
Linear Imager or Laser Bar Code Readers
Gryphon I GD4100/GM4100
Gryphon BT4100/ L GD4300
Product Reference Guide

Datalogic Gryphon L GD4300 Specifications

General

Brand	Datalogic
Model	Gryphon L GD4300
Category	Barcode Reader
Language	English

Summary

Display and Battery

Battery Safety Warnings

Crucial safety instructions for handling and using the device's battery.

Programming the Reader

Programming Barcodes

Instructions on using barcodes to configure reader settings.

Chapter 2 Setup

Setting Up the Reader

Step-by-step guide for connecting and setting up the reader.

Interface Cable Installation

Installing the Interface Cable

Instructions for connecting various interface cables to the reader.

Base Station Configuration

Connecting the Base Station

Guide on connecting the base station to a host device.

Interface Selection

Interface Selection

Guide to selecting the appropriate interface type for host connection.

Setting the Interface

Procedure for scanning programming barcodes to set the interface.

Customizing Configuration Settings

Configure Interface Settings

Instructions for further customizing reader settings after interface selection.

Configuration Management

Resetting the Product Configuration to Defaults

Procedures to restore custom or factory default configurations.

Replacing the Battery

Chapter 3 Configuration Using Barcodes

Configuration Parameters

Overview of configurable parameters organized by type.

RS-232 ONLY Interface Settings

RS-232 ONLY INTERFACE

Settings specific to the RS-232 serial interface.

RS-232/USB-COM Interface Settings

RS-232/USB-COM INTERFACES

Settings applicable to both RS-232 and USB-COM interfaces.

Keyboard Interface Settings

Data Formatting Options

GLOBAL PREFIX/SUFFIX

Adds up to 20 ASCII characters as prefix or suffix to barcode data.

LABEL ID

Configures custom Label IDs as pre-loaded sets or individually.

Reading Parameters

Double Read Timeout

Sets minimum time between reads of the same label.

Good Read: When to Indicate

Specifies when reader provides indication upon successfully reading a barcode.

Scanning Features

Scan Mode

Selects the reader's scan operating mode (e.g., Trigger Single).

CODE SELECTION

DISABLE ALL SYMBOLOGIES

Feature to disable all barcode symbologies simultaneously.

CODE EAN/UPC

Configuration options for EAN and UPC barcode symbologies.

CODE 39

Configuration options for the Code 39 barcode symbology.

CODE 128

Configuration options for the Code 128 barcode symbology.

INTERLEAVED 2 OF 5 / STANDARD 2 OF 5

Configuration options for I2of5 and Standard 2 of 5 symbologies.

CODABAR

Configuration options for the Codabar barcode symbology.

GS1 DATABAR™ Variants

Configuration options for GS1 DataBar Omnidirectional, Expanded, and Limited.

CODE 93 / MSI / PLESSEY

Configuration options for Code 93, MSI, and Plessey symbologies.

Chapter 4 Wireless Features

Bluetooth-Only Features

BT SECURITY FEATURES

Setup for PIN code authentication, device connection, and data encryption.

Chapter 5 Laser Features

BI-DIRECTIONAL READ DECODING

Provides control over good read and barcode label requirement.

Chapter 6 References

RS-232 Parameters

Detailed explanation of RS-232 parameters like Baud Rate and Parity.

RS-232/USB COM Parameters

Parameters applicable to both RS-232 and USB-COM interfaces.

Symbologies

Explanation of decoding levels and length control for symbologies.

LED and Beeper Indications

Table 50. LED and Beeper Indications

Lists indications for power-up, good read, ROM failure, and more.

Error Codes

Describes LED flashes/beep codes associated with detected errors.

Appendix B Standard Defaults

GLOBAL INTERFACE FEATURES

Default settings for Host Commands and USB Suspend Mode.

RS-232 ONLY

Default settings for Baud Rate, Data Bits, Stop Bits, Parity, and Handshaking.

RS-232/USB-Com

Default settings for Intercharacter Delay, Beep options, ACK/NAK.

KEYBOARD WEDGE

Default settings for Country Mode, Caps Lock, Numlock, and more.

Data Format

Default settings for Global Prefix/Suffix and Global AIM ID.

READING PARAMETERS

Default settings for timeouts, beeps, LED indications, and scan modes.

Code Selection

Default settings for Coupon Control and UPC-A symbology.

GS1-128

Default settings for GS1-128 Enable.

ISBT 128

Default settings for ISBT 128 Concatenation and Force Concatenation.

Codablock F

Interleaved 2 of 5

Default settings for I2of5 Enable/Disable, Check Character, and Reads.

Standard 2 of 5

Default settings for Standard 2 of 5 Enable/Disable and Check Character.

Industrial 2 of 5

Default settings for Industrial 2 of 5 Enable/Disable and Check Character.

Code IATA

Datalogic 2 of 5

Codabar

Default settings for Codabar Enable/Disable and Check Character.

Code 11

Default settings for Code 11 Enable/Disable and Check Character.

GS1 DataBar™ Omnidirectional

GS1 DataBar™ Expanded

GS1 DataBar™ Limited

Code 93

Default settings for Code 93 Enable/Disable and Check Character.

MSI

Plessey

WIRELESS Features

Bluetooth-Only Features

Laser Features