Delta C2000 Plus Series - Page 399

Chapter 11 Summary of Parameter SettingsC2000 Plus
11-12
Pr. Parameter Name Setting Range Default

01-15 Deceleration Time 2
Pr.01-45 = 0: 0.00–600.00 sec.
Pr.01-45 = 1: 0.00–6000.0 sec.
The default of motor drive with 30HP and above:
60.00 / 60.0
10.00

01-16 Acceleration Time 3
Pr.01-45 = 0: 0.00–600.00 sec.
Pr.01-45 = 1: 0.00–6000.0 sec.
The default of motor drive with 30HP and above:
60.00 / 60.0
10.00

01-17 Deceleration Time 3
Pr.01-45 = 0: 0.00–600.00 sec.
Pr.01-45 = 1: 0.00–6000.0 sec.
The default of motor drive with 30HP and above:
60.00 / 60.0
10.00

01-18 Acceleration Time 4
Pr.01-45 = 0: 0.00–600.00 sec.
Pr.01-45 = 1: 0.00–6000.0 sec.
The default of motor drive with 30HP and above:
60.00 / 60.0
10.00

01-19 Deceleration Time 4
Pr.01-45 = 0: 0.00–600.00 sec.
Pr.01-45 = 1: 0.00–6000.0 sec.
The default of motor drive with 30HP and above:
60.00 / 60.0
10.00

01-20 JOG Acceleration Time
Pr.01-45 = 0: 0.00–600.00 sec.
Pr.01-45 = 1: 0.00–6000.0 sec.
The default of motor drive with 30HP and above:
60.00 / 60.0
10.00

01-21 JOG Deceleration Time
Pr.01-45 = 0: 0.00–600.00 sec.
Pr.01-45 = 1: 0.00–6000.0 sec.
The default of motor drive with 30HP and above:
60.00 / 60.0
10.00

01-22 JOG Frequency 0.00–599.00 Hz
6.00

01-23
Switch Frequency between the
First and Fourth Accel./Decel.
0.00–599.00 Hz
0.00

01-24
S-Curve for Acceleration Begin
Time 1
Pr.01-45 = 0: 0.00–25.00 sec.
Pr.01-45 = 1: 0.0–250.0 sec.
0.20

01-25
S-Curve for Acceleration Arrival
Time 2
Pr.01-45 = 0: 0.00–25.00 sec.
Pr.01-45 = 1: 0.0–250.0 sec.
0.20

01-26
S-Curve for Deceleration Begin
Time 1
Pr.01-45 = 0: 0.00–25.00 sec.
Pr.01-45 = 1: 0.0–250.0 sec.
0.20

01-27
S-Curve for Deceleration
Arrival Time 2
Pr.01-45 = 0: 0.00–25.00 sec.
Pr.01-45 = 1: 0.0–250.0 sec.
0.20
01-28 Skip Frequency 1 (Upper Limit) 0.00–599.00 Hz 0.00
01-29 Skip Frequency 1 (Lower Limit) 0.00–599.00 Hz 0.00