Denon AVR-1706 Service Manual (English)

Other manuals for Denon AVR-1706

Service Manual98 pages

Brochure & Specs2 pages

Questions and Answers:

N
Nicholas MurphyJul 25, 2025
Why is my Denon Stereo Receiver display lit but no sound is produced?
- A
  Amber SullivanJul 26, 2025
  There are several possible reasons: * The speaker cables might not be securely connected, so ensure they are. * The INPUT SELECTOR knob could be improperly set; adjust it to a suitable position. * The volume control might be set to minimum; increase the volume to a suitable level. * MUTING may be activated; switch it off. * If you've selected digital input, ensure digital signals are being input, or select the correct input terminals.
R
Robert WrightJul 31, 2025
How to fix a Denon AVR-1706 when the display is not lit and no sound is produced?
- D
  Donald SmithJul 31, 2025
  First, ensure the power supply cord is securely plugged in. If that doesn't work, turn the POWER switch on and then use the remote control to turn the power on.
P
Patricia EwingAug 4, 2025
What to do if the display is not lit and the power indicator is flashing rapidly on my Denon AVR-1706?
- S
  scruzAug 4, 2025
  This usually indicates a problem that requires immediate attention. The issue could be: 1. Speaker terminals are short-circuited: Switch the power off, connect the speakers properly, and then switch the power back on. 2. The ventilation holes are blocked: Turn off the power, ventilate well, and allow the unit to cool down before turning it back on. 3. The unit is operating at continuous high power with inadequate ventilation: Turn off the power, ventilate well, and allow it to cool before turning it back on.
D
Daniel MillerAug 10, 2025
Why is sound only produced from one channel on my Denon AVR-1706?
- M
  Manuel GreeneAug 10, 2025
  This issue typically arises from incomplete connections. Check that both the speaker cables and the input/output cables are securely connected.
U
ujohnsonAug 15, 2025
What causes instruments to sound reversed during stereo playback on my Denon Stereo Receiver?
- S
  shannonsextonAug 15, 2025
  This problem is likely due to reversed connections of either the left and right speakers or the left and right input/output cables. Check these connections to ensure they are correct.
C
Corey WashingtonAug 20, 2025
How to stop howling noise when volume is high on Denon AVR-1706?
- T
  Tracie AlvaradoAug 20, 2025
  Howling noise at high volumes can occur if the speaker systems are too close together; try separating them as much as possible. Also, if the floor is unstable and vibrates easily, use cushions to absorb speaker vibrations transmitted by the floor.

Denon AVR-1706 Specifications

General

Speakers connectivity type	-
Receiver type	Surround
Frequency range	10 - 100000 Hz
Audio output channels	7.1 channels
Audio A/D Converter (ADC)	24-bit/96kHz
Total Harmonic Distortion (THD)	0.08 %
Power output per channel (1KHz@6 Ohm)	110 W
Power output per channel (20-20KHz@8 Ohm)	75 W
Composite video out	2
Component video (YPbPr/YCbCr) out	1
AC (power) in	Yes
Composite video in	4
Component video (YPbPr/YCbCr) in	3
AM band range	520 - 1710 kHz
FM band range	87.5 - 107.9 MHz
Supported radio bands	AM, FM
AC input voltage	120 V
AC input frequency	60 Hz
Optical drive included	No
Product color	Black
Audio decoders	DTS 96/24, DTS-ES (Discrete 6.1), DTS-ES (Matrix 6.1), Dolby Digital EX, Dolby Pro Logic IIx
Apple docking compatibility	Not supported