Denon AVR-X4000 User Manual

216
Appendix
SettingsPlaybackConnections
Contents
Front panel Display Rear panel IndexRemote
Tips
Symptom Cause/Solution Page
DTS sound is not output. •Check that the digital audio output setting on the connected device is set to “DTS”.
•Set “Decode Mode” on the menu to “Auto” or “DTS”.
–
171
Dolby TrueHD, DTS-HD, Dolby Digital
Plus audio is not output.
•Make HDMI connections.
•Check the digital audio output setting on the connected device. On some devices, “PCM” is
set by default.
41,42
–
Dolby PLg mode or DTS NEO:X mode
cannot be selected.
•It cannot be selected when “None” is set for “Speaker Config.” – “Center” and “Surround”.
•These cannot be selected when using the headphones.
182
–
Audyssey MultEQ® XT32, Audyssey
Dynamic EQ®, Audyssey Dynamic
Volume® and “Audyssey LFC™”
cannot be selected.
•These cannot be selected when you have not performed Audyssey® Setup.
•Switch the sound mode to other than “DIRECT” or “PURE DIRECT”.
•These cannot be selected when using the headphones.
172
114
–
Audyssey DSX® cannot be selected. •It can be selected when using the front height or front wide speakers.
•It can be selected when using the center speaker.
•Switch the sound mode to DOLBY sound mode or DTS sound mode.
•This cannot be selected when using the headphones.
184
182
113
–
“Restorer” cannot be selected. •Check that an analog signal or PCM signal (Sample Rate=44.1/48 kHz) is input. For playback
of multichannel signals such as Dolby Digital or DTS surround, “Restorer” cannot be used.
•Switch the sound mode to other than “DIRECT” or “PURE DIRECT”.
155
114
No audio is output from PRE OUT or
speakers for ZONE2/ZONE3.
•In ZONE2/ZONE3, the audio can be played back when signals input from digital connectors
(OPTICAL/COAXIAL) are in 2ch PCM format.
•In ZONE2, the audio can be played back when signals input from the HDMI connector are
in 2ch PCM format. To play back the audio in ZONE2 irrespective of the input signal format,
set the “HDMI Audio” setting in the menu to “PCM”. Depending on the played back device,
the audio may not be played back even with this setting. In that case, set the audio format to
“PCM” on the played back device.
–
194

Denon AVR-X4000 Specifications

General

Receiver type	-
Frequency range	10 - 100000 Hz
Output impedance	16 Ω
Speaker selector	A+B
Input sensitivity	200 mV
Audio output channels	7.2 channels
Signal-to-Noise Ratio (SNR)	102 dB
Total Harmonic Distortion (THD)	0.008 %
Power output per channel (1KHz@6 Ohm)	165 W
Power output per channel (20-20KHz@8 Ohm)	125 W
HDMI in	7
AC (power) in	Yes
Composite video in	4
Ethernet LAN (RJ-45) ports	1
Component video (YPbPr/YCbCr) in	2
Number of HDMI outputs	3
Connectivity technology	Wired
Speakers connectivity type	Banana connector
Audio formats supported	AAC, FLAC, MP3, WAV, WMA
Image formats supported	JPG
Wi-Fi	No
RDS features	PTY, TP
FM band range	87.5 - 108 MHz
Supported radio bands	FM
Internet radio services supported	Spotify, vTuner
Supported video modes	1080i, 1080p, 480p, 576p, 720p
Display	VFL
Color depth	24 bit
Aspect ratio	4:3, 16:9
Product color	Silver
Audio decoders	Dolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, Dolby TrueHD, DTS-ES (Discrete 6.1), DTS-ES (Matrix 6.1), DTS-HD, DTS-HD Master Audio
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Apple docking compatibility	Not supported
AC input voltage	230 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.1 W
Power consumption (typical)	670 W

Weight and Dimensions

Depth	379 mm
Width	434 mm
Height	167 mm
Weight	12300 g