Design Analysis H-522 User Manual (English)

To Next Page

XL™ Series

Models H-350XL™

H-500XL™

H-510XL™

H-522

H-522 - Plus

Owner’s Manual

Default Chapter3
- Table of Contents3
Chapter 1 Introduction11
- Introduction to the XL™ Series Data Logger11
- Unpacking the XL™ Series Data Logger12
- Modes of Operation12
- Sensor Mode13
- Data Logger / DCP Master Mode13
- Operation Using Auxiliary Outputs13
- Operation with the H-355 Gas Purge System (Bubbler)14
- About this Manual14
- Advanced Manual Sections14
- Web14
Chapter 2 Hardware Options and Installation15
- Mechanical Mounting15
- Front Panel Description15
- Earth Ground Lug16
- Pressure Reference Port (Vent)16
- Pressure Port (Input)16
- GOES Antenna Output17
- GPS Antenna Connector17
- Sample Installation for the Conoflow System18
- Making the Pressure Connection to the H-355 Bubbler19
- Bubbler / Aux Port20
- Ports21
- Analog Input Section22
- Analog Input Channels22
- Analog Grounds22
- Switched +5 Volt Reference Excitation23
- Wind Speed Input (AC Frequency Input)23
- Event Counter Input24
- To 20 Milliamp Output25
- Digital I/O 1 and 226
- SDI-12 Section27
- Power Connections28
- Testing the Installation28
- Hardware Revision Detection29
Chapter 3 Using the Built in Keypad / Display31
- Overview31
- Keypad/Display Operation31
- Familiarization36
- Main Menu Description37
Chapter 4 Using the PC Menu Interface Operation43
- PC Menu Interface43
- PC Menu General Operations44
- Main Menu Screen45
Chapter 5 General System Options47
- Overview47
- System Setup47
- Time Sync Options51
- Advanced System Setup Options54
Chapter 6 Serial Port Options59
- Introduction59
- Serial Port Menus59
- Serial Port Hardware Description64
- Serial Port Functions64
Chapter 7 System Configuration Files67
- Overview67
- Configuration Files Menus67
- Sample Configuration File69
Chapter 8 System Status Menus / Optioons75
- Status Options Overview75
- Status Menus75
- Status Screen Operations76
Chapter 9 Scanning Options85
- Introduction85
- Scanning Menus85
- Scanning Options85
Chapter 10 Stage Menus / Options93
- Stage Options (H-350XL / H-510XL Only)93
- Remote Stage Setup Overview93
- Remote Stage Menus93
- Remote Stage Options93
Chapter 11 Analog Inputs / 5 Volt Excitation95
- Analog Inputs Overview95
- Analog Menus95
- Analog Options96
- Analog Input Connections98
- Analog Inputs and Analog Ground Connections98
- Switched +5.00 Volt Reference Excitation99
- Analog Input Setup Examples99
- Two Point Calibration Basics101
Chapter 12 Digital I/O103
- Digital I/O Overview103
- Digital I/O Menus103
- Digital I/O Options104
- Quadrature Shaft Encoder Options109
Chapter 13 Counter and Frequency Inputs111
- Introduction111
- Counter and Frequency Menus111
- Counter Options112
- Frequency Options115
Chapter 14 SDI-12 Operations117
- Overview117
- Transparent Mode and Full Screen Mode117
- Data Logger Mode122
- Sensor Mode125
- H310 Setup128
- H330 / H331 Setup130
- Sensor Mode Supported Commands132
- Command and Response Protocol133
- Standard SDI-12 Command Set134
- Send Acknowledge Command134
- Send Identification Command135
- Measure Command136
- Initiate Verify Command137
- Send Data Command139
- Change Sensor Address139
- Extended SDI-12 Command Set140
- Write "User Units Slope" Command141
- Write "User Units Offset" Command141
- Read User Units Slope" Command141
- Read "User Units Offset" Command144
Chapter 15 Logging Options145
- Logging Overview145
- Logging Options Menu145
- Logging Options145
Chapter 16 Operation with the GOES Radio157
- Introduction157
- GOES Radio Data Connection157
- GOES Radio Types157
- Configuring the GOES Radio, General Options159
- GOES Self Timed Options166
- GOES Random Options180
- GOES Diagnostics184
- GOES Radio Setup Example187
- GOES Binary Data188
- GOES Four Byte Pseudo-Binary Lookup Table190
- Common GOES Terms191
- Julian Day Tables193
- GOES Downlink Message Header Basics195
Chapter 17 ALERT Radio Operation199
- Introduction199
- ALERT Menus199
- ALERT Options200
- Special Cases for ALERT Transmissions206
Chapter 18 4 to 20 Milliamp Output207
- Introduction207
- To 20 Milliamp Menus207
- To 20 Milliamp Options207
- To 20 Hardware Connections / Wiring210
Chapter 19 Alarm Call out211
- Overview211
- Alarm Call out Menus211
Chapter 20 Data Card Options217
- Data Card Options217
- Data Card / Memory Options218
Chapter 21 Operation with the H-355 "Smart Gas" System227
- Menus227
- Introduction to the H-355227
- Options228
- Configuration Drawing233
Chapter 22 Functions235
- Introduction235
- Function Menu235
Chapter 23 XL-Basic Programming Guide248
- General Purpose Variables248
- Standard Input Variables249
- Read Only Variables250
- Math Functions251
- XL-Basic Command Summary252
- Creating XL-Basic Programs264
- XL-Basic Menu Screens264
- Example Program #1266
- Example Program #2267
Chapter 24 Maintenance / Troubleshooting269
- Maintenance269
- Troubleshooting269
Appendix A XL Series Specifications271

Need help?

Do you have a question about the Design Analysis H-522 and is the answer not in the manual?

Design Analysis H-522 Specifications

General

Brand	Design Analysis
Model	H-522
Category	Data Loggers
Language	English

Related product manuals

Design Analysis H-350XL

272 pages

Design Analysis H-522 User Manual

Table of Contents

Design Analysis H-522 Specifications

Related product manuals