This document is an Owner's Guide for Directed security/keyless entry and remote start systems, specifically models 5305V, 5305P, 5305X, 5305A, and 5305L. It provides comprehensive information on the system's features, operation, and maintenance.
Function Description:
The Directed system is a state-of-the-art security/keyless entry and remote start system designed for fuel-injected, automatic transmission vehicles only. It offers various functionalities to enhance vehicle security, convenience, and remote control. The system can be either a security system or a keyless entry system, with some features being exclusive to security systems.
Important Technical Specifications:
The system includes a 2-way LCD remote control and a 4-button 1-way remote control. The 2-way remote control features an internal antenna for transmitting and receiving information, a display for command response feedback and system states, and four command buttons for arming/locking, disarming/unlocking, auxiliary channels, and remote start. A programming button on the back of the remote allows user selection of LCD remote control response options. The Control Center, typically located on the upper part of the front windshield, houses the antenna for 2-way communication and includes a control center LED (status LED) as a visual indicator of the system's status. The 2-way remote control is powered by one 1.5V AAA battery, while the 1-way remote control is powered by either two 3V CR2016 batteries or one 3V CR2032.
Usage Features:
- Basic Commands:
- Arm/Lock: Press and release the lock button. The alarm arms, doors lock (if connected), and the siren/horn sounds with parking lights flashing once. If Valet mode is on, doors lock without audio confirmation.
- Panic: Press and hold the lock button. The alarm arms (or locks in Valet) and, after two seconds, sounds the siren/horn and flashes the parking lights. Press and release the lock button again to stop panic.
- Disarm/Unlock: Press and release the unlock button. The alarm disarms, doors unlock (if connected), and the siren/horn sounds with parking lights flashing twice. Also turns panic off. If Valet mode is on, doors unlock without chirp confirmations.
- Silent Mode™: Press and release AUX or the remote start button before the Arm/lock or Disarm/unlock command to use the remote control in Silent Mode.
- Optional Function (Trunk Release): Press and hold AUX or the remote start button to activate the Aux output for functions like trunk release.
- Remote Start: Press and release the remote start button (once or twice, depending on programming). Activates (or deactivates) the remote starter. The engine and parking lights turn on. The vehicle runs for a pre-programmed period (12, 24, or 60 minutes) or until a shutdown input is triggered.
- Advanced Commands:
- Additional Auxiliary Functions: Press the lock and AUX buttons simultaneously for auxiliary 4, unlock and AUX buttons simultaneously for auxiliary 5, or lock and remote start buttons simultaneously for auxiliary 6.
- Timer Mode: Press the lock and remote start buttons simultaneously. Keeps the engine warm by automatically activating remote start every three hours for a maximum of six cycles (timed mode) or checks temperature every three hours and starts if below 0°F (temperature mode). Exits automatically after 18 hours in temperature mode.
- Short-run Turbo Mode: Press the remote start and AUX buttons simultaneously. Keeps the engine running for a programmable period after arriving at your destination to cool down the turbo.
- Optional Rear Window Defogger: Automatically activates during remote start if the control module temperature is below 55°F.
- Multi-car Control Capability: The 2-way remote control can operate up to four vehicles. Press the P button on the back for one second to switch between vehicles.
- Paging Features: The control module sends a page to the remote for command confirmation or alarm status. The remote beeps or vibrates and displays the armed/locked or disarmed/unlocked status. If triggered, the LCD displays the zone. Press any button to clear the page.
- Remote and System Operations:
- Passive Arming/Locking: System automatically arms/locks 30 seconds after ignition is turned off and a door is opened/closed. Status LED flashes twice as fast during countdown, siren/horn sounds at 20 seconds, and parking lights flash at 30 seconds.
- Warn Away® Response (security only): Light impacts trigger vehicle lights and siren/horn for a few seconds, 2-way remote beeps ten times (or vibrates once), and enters Page Recognition Mode.
- Triggered Response (security only): Activated by various triggers (shock sensor, door, hood, trunk, ignition). Siren/horn sounds and lights flash for a programmed duration (default 30 seconds, programmable 1-180 seconds). 2-way remote repeats four quick beeps (or vibrates) for 15 seconds, and the full trigger alert icon turns on.
- Multi-level Security Arming (security only): Allows selection of active or bypassed sensors/inputs. Press the lock button consecutively to cycle through security levels, bypassing specific zones. Applies to a single arming cycle.
- Arming While Driving (security only): Press the lock button for two seconds while the vehicle is running. Siren/horn sounds once to confirm arming. Disarms when ignition is turned off or by pressing the unlock button.
- High Security Disarm (security only): If the system is triggering for longer than six seconds, pressing the unlock button will stop the trigger and return the system to an armed state (reset). Pressing the unlock button again disarms the system. Pressing the unlock button during the first six seconds of a triggered sequence disarms immediately.
- System (Emergency) Override: Manually disarm the system or disable the starter kill if the remote is lost or damaged. Turn ignition to ON, then press and release the control center button the preset number of times (default 1 press) within 15 seconds.
- Valet Mode: Prevents automatic arming/locking and triggering. All convenience functions (door locks, trunk release) still work. To enter/exit: turn ignition ON, then OFF, then press and release the control center button within 10 seconds. Alternatively, open any vehicle door, press unlock, then press lock and unlock simultaneously. Status LED lights solidly in Valet Mode and turns off when exiting.
- Pit Stop Mode: Allows the vehicle to remain running after the key is removed. Useful for short stops while keeping the engine and climate controls on. To activate: set parking brake, press and release the remote start button (programmed amount of times), then wait five seconds. Turn ignition key to OFF, exit, and secure the vehicle.
- Nuisance Prevention Circuitry (NPC): Prevents repetitive false alarms from faulty switches or environmental conditions. If the same sensor/switch triggers the alarm three times within 60 minutes, NPC bypasses that zone for 60 minutes. Doors are bypassed until the trigger ceases after three full cycles.
- Power Saver Mode: Automatically enters while armed or in Valet Mode after a period of inactivity to lower current draw. In armed state, LED flashes at half rate after 24 hours. In Valet Mode, LED turns off after one hour of no ignition activity.
- Diagnostics (security only):
- Arming Diagnostics (Bypass Notification): If armed with an active input (e.g., door open), the unit chirps once, then again a few seconds later. The system ignores the active zone until the input stops.
- Disarming Diagnostics (Tamper Alert): Four chirps indicate a trigger in your absence. Five chirps indicate a zone was bypassed by NPC. The control center LED indicates the triggered zone by blinking a pattern.
- Programming the LCD Remote Control:
- To enter programming mode: Press and hold the P button on the back of the remote until one long beep sounds.
- Beeps and Vibration, On/Off: Press the lock button to select beeps only (1 beep), vibrate only (1 vibrate), beep & vibrate (1 beep & 1 vibrate), or no beep & no vibrate (1 long beep).
- Illumination On/Off: Press the unlock button to select LCD backlight illumination On (1 beep backlight On) or Off (2 beeps backlight Off).
- Page Notification: Press the remote start button to select page On (1 beep) or Off (2 beeps). When Off, only command responses are received, not alarm trigger pages.
- To exit programming mode: The remote exits after five seconds of inactivity and emits two long beeps.
- Owner Recognition: Allows programming different settings for each remote control using a Directed Bitwriter, supporting up to four users with personalized settings.
- Rapid Resume Logic: Stores the system's current state (armed, disarmed, Valet Mode) in non-volatile memory, recalling it if power is lost and reconnected.
Maintenance Features:
- Battery Level Indicator, 2-way: Four level indicators show battery charge. A single notification chirp and continuous flashing of the indicator signal low battery.
- Battery Replacement, 2-way remote control: Gently pull the battery door, slide it up, replace the 1.5V AAA battery (observing polarity), reinstall the door. Remote plays a melody and displays all icons when power is returned.
- Battery Replacement, 1-way remote control: Use a small flat-head screwdriver to pry open the unit, remove the rear housing, replace the two 3V CR2016 batteries or one 3V CR2032, and reassemble.
- Battery Disposal: Dispose of batteries according to municipal requirements.
- Upgrades and Batteries: Any upgrades or battery installations must be performed by an authorized dealer. Unauthorized modifications void the warranty.
- Water/Heat Resistance: The product is not designed to be water and/or heat-resistant. Keep it dry and away from heat sources to avoid voiding the warranty.
Security & Convenience Expansions (Optional):
- Audio Sensor (506T): Detects metal on glass, cracking glass, and breaking glass.
- Backup Battery (520T): Keeps the system armed and starter kill active if main battery power is disconnected.
- Field Disturbance Sensor (508D): Establishes an invisible dome of coverage, reacting to intrusions.
- Headlight and Parking Light Automation (545T Nite-Lite): Automatically turns on parking and headlights when dark or when windshield wipers are used. Can also be used for a programmed time via remote.
- Power Trunk Release: Operates a factory power release for the vehicle's trunk or hatch.
- Power Window Control (529T and 535T systems): Provides automatic power window control.
- Tilt Sensor (507M): Triggers an alarm if the vehicle is lifted, protecting rims.
- Ultrasonic Sensor (509U): Provides a field of protection inside the vehicle.
Government Regulations:
The device complies with Part 15 of FCC rules and Industry Canada Radio Standards Specification RSS 210. It is subject to two conditions: (1) it may not cause harmful interference, and (2) it must accept any interference received. Users are advised to reorient/relocate the antenna, increase separation from other equipment, or consult a technician if interference occurs. Changes or modifications not expressly approved by the responsible party could void the user's authority to operate the device.
Safety First Warnings:
- Never remote start the vehicle with keys in the ignition (except Pit Stop mode) or if it's not in PARK or NEUTRAL.
- Do not activate remote start if the vehicle has a manual transmission.
- It is unsafe to operate a vehicle's motor in a garage or other closed-off area due to hazardous exhaust.
- For manual transmission vehicles: ensure the vehicle is in neutral, no one is standing near it, remote start on a flat surface, and the parking brake is engaged.
- The owner is responsible for ensuring the parking/emergency brake functions properly and should have it inspected biannually.
- Never remotely start a vehicle in gear or with keys in the ignition. The neutral safety feature should be periodically checked by an authorized Directed dealer.
- If the vehicle starts in gear, cease remote start operation immediately and consult the dealer.
- Use of this product in a standard transmission vehicle must be in strict accordance with this guide.
- Should not be installed in convertible vehicles, soft or hard top with a manual transmission, as it may pose certain risks.
- Interference: All radio devices are subject to interference.
Warranty:
Directed offers a limited lifetime consumer warranty for the unit (excluding siren, remote transmitters, sensors, and accessories, which have a one-year warranty). The warranty is valid if purchased from and installed/serviced by an authorized Directed dealer, and returned with proof of purchase. It is void if the unit's serial number is defaced, modified, or damaged by accident, unreasonable use, neglect, improper service, or installation. Directed disclaims liability for theft, damage, or vandalism and does not cover labor costs for maintenance, removal, or reinstallation. The maximum recovery under any claim is limited to the authorized dealer's purchase price. Some states do not allow limitations on implied warranties or incidental/consequential damages. The warranty is valid for sales in the US and Canada. Products sold outside these regions are "AS-IS" with no warranty.
Need help?
General
To Next Page