Directed Directechs DB3 - User Manual

24 pages

Save Page as PDF

To Next Page

INSTALLATION GUIDE

DB3

2020 Audi Q7 (Smart Key). 403.VW08 1.35 RSR

This product is intended for installation by a professional installer only! Attempts to install this

product by a person other than a trained professional may result in severe damage to a vehicle’s

electrical system and components.

Questions and Answers

M
Miss Jessica WilliamsSep 6, 2025
Why Directed Directechs DB3 speed was detected?
- R
  Ryan SchultzSep 6, 2025
  The vehicle was detected as moving, which prevents the system from shutting it down.
J
Jason BowmanAug 28, 2025
What to do if ISO 1 is not detected in Directed Directechs DB3 Automobile Accessories?
- Y
  ymillerAug 28, 2025
  The Yellow/Black wire did not detect the expected signal. Check the connections.
J
Janice VillegasAug 26, 2025
What does ISO 2 not detected mean for Directed Directechs DB3 Automobile Accessories?
- R
  Robert DeanAug 26, 2025
  If ISO 2 is not being detected by your Directed Automobile Accessories, it means the Orange/Black wire didn't detect the expected signal. Refer to “Installation (wiring diagrams & vehicle wiring reference charts)” to check the connections.
D
David BarnesSep 8, 2025
What does 'Runsafe was not disabled' mean on my Directed Automobile Accessories?
- T
  Thomas WeaverSep 8, 2025
  No UNLOCK command was received prior to opening the door, or the 45 second timer expired in takeover mode.
M
Mark MillerSep 7, 2025
What to do if my Directed Automobile Accessories system displays 'Bypass processing error'?
- S
  sallytorresSep 7, 2025
  The bypass calculation failed. Reset the Directed Automobile Accessories module and try again. If the condition persists, please contact Technical Support.
P
Phillip EllisonAug 29, 2025
Why was the smart key not detected by Directed Automobile Accessories?
- B
  bowenbrandonAug 29, 2025
  The smart key was not detected, which prevents the system from shutting down the vehicle.
M
Maria MclaughlinAug 30, 2025
What to do if Directed Directechs DB3 Automobile Accessories is waiting to begin the programming sequence?
- E
  Elizabeth BurkeAug 30, 2025
  Make sure you are following the correct programming procedure.
S
Sheri MartinezSep 1, 2025
What to do if Directed Directechs DB3 Automobile Accessories says CAN2 not detected?
- J
  Jennifer HarrisSep 1, 2025
  Check the CAN2 Orange/Green and Orange/Brown wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times.
M
Mrs. Kathy RogersSep 5, 2025
What does 'RFTD disabled' mean in Directed Automobile Accessories?
- R
  Ronald MasseySep 5, 2025
  If the Directed Automobile Accessories system indicates 'RFTD disabled,' 3x OEM Lock Remote Start Activation was attempted when the RFTD feature is disabled. Make sure 3x Lock Start is selected from the web in the flashing process.
J
Jordan JohnsonSep 23, 2025
What does it mean if Directed Directechs DB3 Automobile Accessories says ISO 2 not detected?
- L
  Linda ShortSep 23, 2025
  If the Directed Automobile Accessories system indicates 'ISO 2 not detected,' it means the Orange/Black wire did not detect the expected signal. Consult the “Installation (wiring diagrams & vehicle wiring reference charts)” to verify the connections.