Rev.: 20 708115
Platform: DBALL2
Firmware TL6:
© 201 Directed.7 All rights reserved.
14
(-) Trunk Status Input
[]1 ( ) T Status InputAC ach
(-) Door Status Input
(-) E-Brake Status Input
Remote
Starter
(-) (Status)GWR
(-) OutputLock
(+) Starter Output
(-) OutputUnlock
(-) Trunk OutputRelease
(+) 12V Input(+) 12V
(-) Ground
(+) Brake Input
(-) Hood Status Input
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
(-) Ground: 12Brown :/Red
(-) Output:SLP 11Yellow :/Red
(+) 12V :Input 13Red:
(-) Ground: 14Black:
(+) Brake Output: Gray: 6
(-) Hood Status Output: 9Violet/Brown:
Immo Data 1: Yellow/Black: 10
(+) Ignition Status Output: Gray/Black: 7
Immo Data 2: Orange/Black: 11
(-) Push-to-Start Output: Green/Black: 2
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
[1] ( ) Tach Output: 5AC Violet/White:
(-) Parking Lights Output
(-) Lock Output: Blue/Red: 12
Do not connect these wires:
accessory ignition starter, , from
the remote starter to the vehicle.
Black/White: 1
(-) E-Brake :Status
Certification ECU
(white 30-pin connector)
1
7
2
8
3
6
9
21
22
25
10
13
23
26
11
14
29
24
27
12
15
18
20
19
30
45
16 17
28
Diagnostic Connector OBDII
(connector side view)
18
169
(-) SLP:
Pink, pin 4
Steering Lock
(black onnector)7-pin c
12
3
5
4
7
6
PTS: pin 30Violet,
(+) Ignition Input/Output
Fuse 7.5A
HS CAN High:
Blue, pin 6
HS CAN Low:
pin 14White,
(+) :12V
Blue, pin 16
BTX:
Blue, pin 25
BRX:
Red, pin 26
(-) Unlock:
Gray, pin 24
(-) Lock:
Red, pin 11
Body ECU
(white 30-pin
onnector)c
1
78
19 20
32
910 1312 15 181716
21 22 2723 30
6
4 5
28 29
2625
24
11
Main
Body
ECU
(-) ReleaseTrunk : pin 5Red,
Body ECU
(white 28-pin onnector)c
1
2
34
17 18 19
282522 272423 262320
161310 151297141186
5
8: (+) Starter InputViolet:
10: Blue/White:
(-) (Status) InputGWR
9: (+) Ignition InputPink:
Not required in D2D mode.
Autolight Interrupt (veh. side): 9Orange/Yellow:
Autolight Interrupt (conn. side): 8Yellow:
(-) lights:Auto
pinGreen, 28
diode 1A
(-) Parking lights:
pin 30White,
P#: 2D65XKD
Page 5
10
2DBALL
RF
Prog utton. B
LED
4
14
12
2
Installation Type 1
TX
(-) Ground
RX
(+)12V
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the diagnostic connector.OBDII
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
diodes 1A
To Next Page
Loading...
Need help?
General
